When I have Whisperers, the system appears to calculate the average over the day about 4 degrees higher than for zones without Whisperers.

It seems that, even though the weather data is available throughout the day, that zones without sensors only use the forecast high and low.

This is insufficient to correctly adjust for the amount of watering required.

For example, today is 7 degrees C up to 36.

Whisperer zones average the temp at 26C while non-Whisperer zone calculate the average at 22C.

On these extremely hot days, the non-whisperer zones are under-watering much more than the Whisperer zones.

Also note that even the zones with Whisperers always under-water and needs custom programs or manual intervention.

This finally explains to me why zones are always under-watered.

Can the system please use multiple day readings for non-Whisperer zones and PLEASE provide more watering?

Hello,

I have 2 Whisperer for automatic regularion of my watering.

They work normally work perfekt but when the bad weather prevents charging for o longer period they go to sleep/closes down.

Then my Netro thinks the soil is dry 0% humidity and aut starts my watering eventhough the soil is 90%.

I have ti disable the Netro to stop watering until the Whispering is charged.

Since I do not get any warning that the Wispering power is too low the aut watering can go on and on wasting my water and flooding my garden!

I have one particular zone that i only require watering for 15 seconds every second day.

How can i do this?  i was able to do it on my previous OpenSprinkler.

My two whisperers stopped due to lack of sun. The new one started communicating again.

The old one started communicating but then stopped while the battery was still above 90%.

Seems a communication problem 

Blue light blinking turned quickly to white light blinking.

After blinking a few minutes it stopped but is not connected to the App.

Tried putting it ON close to controller and then close to WiFi router, the result is the same, no connection.

Is the whisperer dead ? Should I buy a new one ?

Thanks

My system keeps watering despite the fact that it is winter with snowy conditions. It schedule to follow city city restrictions. Why?

I just got a Whisperer 2 and it won’t charge past 90%. It’s been plugged in all day. Is the battery defective?

Hello! I would like to set up my system to skip watering if soil moisture reads above a certain threshold. I have the Whisperer and the Pixie, so would like the Whisperer to communicate with the Pixie, so the Pixie skips watering if soil moisture is high enough. Is this possible? Thanks for your help. 

I would.love to have the app inform me when watering starts and stops. Is there a way to do it?

The whisperer sensor combined with the app seems confused. The app tells me to water every day however the sensor tells me a date on when to water next that is usually 8+ days later. 

The app doesn’t seem to talk to itself as far as the reminders are concerned.

(Update 3/17: I still get the notification to water every day, and the sensor still gives me a date over a week away on average)

How do I connect my sensors to zones? I have the latest.

Is there a way to give info to the app to dial in the soil moisture level?   I would like to measure soil moisture and input the info to my controller and the controller should adjust watering schedule. How about reminding user to check moisture level once in a while and input the info. Is this a thing? 

Thanks!

John

Is there a version of the app that runs on a Windows PC or a Raspberry Pi?

I run all my home automation on a dedicated Raspberry Pi so it would be nice to keep everything in one place.

Could you please ask Support to reply to my emails? The subject line of them is,"Whisperer 2 bad solar panel"

Hi I bought and installed a Netro Sprite6 watering controller about a year ago. Would really appreciate having notifications enabled for all watering activities. I had a good look through the app features and can’t find anyway to enable it. Could someone help please?

Bought a new whisperer as an old one is no longer working.

REMARK : WHILE I LIVE IN A TEMPERATE AREA NONE OF MY WHISPERERS LASTS MORE THAN 26 MONTHS WHICH IS SURPRISING AS IT IS NOT SUPPOSED TO BE A CONSUMABLE.

Clicked as required first blinking blue light then blinking white light.

Went to sensors and see the dead old one, the working one but do not see the newly bought one.

Do not see either a + sign to add a new one.

What should I do ?

Hi,

Any chance of adding a valve/solenoid finder feature? This would work similar to products like Chatterbox. The selected station for valve finding would switch the valve on and off quickly so that the rattle/chatter sound it makes can be used to find it. The main valve could be left closed.

Thanks

Is there any way to get a mode for a zone  that keeps grass seed wet enough to germinate? 

Bonjour,

Je n'arrive pas à faire fonctionner les notifications sur mon téléphone Android.

J'aimerais avoir de l'aide.

Merci 

Developers, can you add some indication to list of programs to see which is enabled, which is not?

Instead of going into each and scroll to the very bottom to check 'enabled'.

I think of either being grayed out or adding a sign, whatever simplest may work.

thank you

can anyone help how to reorder programs?

When edit turned on, I just cannot grab marks to the right to pull up or down. So what is that sign for (like > =)?

Mark on left at each program is to delete. That's okay.