Hi- it has been raining now for two weeks and it says moisture level 100% but still watering everyday?  

This is an easy question 

Thanks

My sprinklers are starting 1 hr past when they are programed due to daylight savings ending.

I would have assumed the clocks changed with the clock on my phone but that doesn't seem to be the case. 

Haow can i change this? 

New system owner. When having fall blowout performed, I found I needed to be present to run each zone. I didn’t find a way to provide access to the technician. Other systems on the market provide this function. 

Manually watering Zone 2, sprinklers stopped watering while the app still showing watering and counting the time, tried all other zones, none is watering though the app shows they’re. Checked wifi works, power to the controller works. The only thing I noticed is that the light on the controller is off all the time except when unplug and plug it back, the light flicks once and then remained off

It’s like the app doesn’t know it’s connected 

To the correct WiFi although it is.  Bought a new sensor - not connecting since upgrade to iOS 13. Please advise. See pictures. 

You mentioned you would add the ability to display the ip address in the next upgrade. Having dealt with networking issues for many years. I find it best to be able to assign static ip addresses to my home networked devices so I don’t have random dhcp issues causes by laptops or phones reconnecting and trying to take over an IP address that might be in use by a device that is a permanent resident.

Would you add the ability to assign the IP address to the controller? Many people don’t realize the significance of this but I find it important to a healthy home network.

I've been using my sprite with a Whisperer since a few months. The sprite works wonderfully but the whisperer has serious probloms. I get incorrect readings. Specifically my whisperer is stating 1% topsoil moisture level. Honestly this is impossible after a sprinkling succeded at 6:00 this morning. This misbehaving is going on since the first week. It works for the first day or two after resetting the whisperer but then it goes weird. On other occasions instead the topsoil moisture was stuck at 98% even after several days of not sprinling in full summer with temperatures over 35°. 

I have tried anything from resetting the whisperer to changing spot. At this point I'm led to think that the whisperer is broken.

Is anybody else having this strange behavior?

Do you have any other suggestion to solve this problem?

I have noticed that you are not giving due importance on support requests in this forum about whisperer problems. In my opinion you should put more effort into this.

https://netrohome.com/forum/posts/73/show_question

https://netrohome.com/forum/posts/132/show_question

https://netrohome.com/forum/posts/199/show_question

https://netrohome.com/forum/posts/289/show_question

https://netrohome.com/forum/posts/366/show_question

https://netrohome.com/forum/posts/392/show_question

Thank you

Good product but there is not a windows 10 APP or the possiblity to setup by browser directly to IP address of netro. There is not web server inside.

How to determine prior watering schedule?

My system says it watered yesterday, which it didn’t, and it’s telling me the next watering is in 8 days during my 100 degree days.  What’s going on?

My 2nd watering cycle on even numbered days is during the highest heat of the day and it’s burning my shrubs in zone 4.  Why not once a day in evening hours for good soaking?

Hi. 

We r in Toronto canada and we have extremely cold winter , every year we are asking expert to come and drain the water from the system. I would like to know can i do same with running cycle or still i have to ask expert to come and drain the system?

Would it be possible to publish your API? I (and I'm guessing many others) would like to be able to integrate Netro into tools like Home Assistant

Hi,

I have searched the Netro skill in the Italian Amazon market but wasn’t able to find it.

What do I need to search for?

Thank you

Having a problem since upgrade of the app. Doesn't seem possible unless the main unit updated as well. Valves close within a few minutes of being activated by manual start, or programmed schedule. Have not test with smart watering disabled, but it happens on manual starts, so not sure that is even a variable. The Zone still shows as actively watering in the application. If you submit a stop  action by pressing the red square,then restart, via the sideways triangle, the zone will come back on again. However, it shortly shuts back off, while still showing the zone as being actively watered. This is happening across all four of my zones. Curiously, if you unplug the controller after the valve shuts off, but the app still shows it watering, wait a bit, and then plugit back int-the zone comes backon shortly after reboot.

I'm thinking of buying Netro Sprite, but I have some questions ...

Suport MQTT? 

Suport REST API?

any plans to integrate with Home Assistant?

Thanks in advance...

To the Netro community:

We recently have launched an update for the Netro app on App Store. In the newest iOS version (2.3.0) of the app, Apple Watch is now supported.

In the watch app, users will be able to check the status of the device, the weather data, zone status and view watering schedules in the next 7 days.

Please feel free to explore other new and exciting features that we just added (also available on Android) : 

1.Support Weather Underground PWS

(Settings->Controller->Weather Provider)

2.Rainfall adjustment

(Please go to the Discover page and tap the "+" button on the upper right corner,  select "Correct Rainfall")

3.Enable plant sensors to monitor multiple zones

( Settings->Sensors, select a sensor, go to Zones and select the zones you would like to monitor)

Regards,

Netro Support

When are you planning release firmware update for sprite having issue connecting to wifi after power issue? This happens quite a bit and my sprite is off line.

Post install and after first unsuccessful run, it says it watered but it definitely did not, I found an extra wire that I had plugged into ‘C’ next to the ‘M’, that I had left unplugged in my last successful Netro setup. I have now unplugged it and did another unsuccessful run. My question is, when making a wiring tweak like that do I need to press the ‘RST’ before proceeding with a run?