I have installed a new Sprite - however, I have 3 common wires but only two slots - and only one wire fits in each slot...

How do I change and save schedule? 

Anyone else have problems with whisperer/whisperer 2? The ones I have just seem to stop working out the blue.  The current problem unit is a whisperer 2 which was sent to replace a broken whisperer.  It comes on, lights up, and shows 100% charged when plugged into a usb power source.  As soon as I unhook the power source it stops working, and oower button does nothing.

I have a digital water metering in my house from my water supplier. So know the exact amount of water that ist running for all zones If netro ist running and watering the Garden. Unfortenately i can Not find an Option, to Tell netro how much water in qm per hour is running for wach zone. IT would be great If that could be implementated to have an exact number of qm water that ist uswd for watering each zone. So gar I know netro gives only an wstamated number of water used for wach zone, depwnding in size of watering area and Type of watering equipment.

I can't connect both of my two Pixie devices to Alexa — I can only control one.
How can I fix this issue?

Thank you.

Help for my controller dropping the wifi weekly?  I have to unplug the controller to reset and wifi works.  When on vacation my controller can't be unplugged so is there a fix or work around ?

My app on my phone say that the zone is on watering but when i look outside nothing is happening !!!

Hello, I have activated Continuous Monitoring on my Wispering gen2 which means I should get an emediate update when the moister has changed.

But I don't get any update/ change until the aut hourly upate of the measurement is done.

My indicator led is burn out. whocan I replace it?

Could you add a pause feature in Manual run? When I am running a zone, sometimes I need to halt the run and make an adjustment or fix a leak and then turn it back on. Right now, I have to stop the manual run and then start all over. 

I have one sensor that is controlling 5 zones, in the last few months it has rained for several days and the humidity recorded has always been 100%. For three weeks however it has not rained anymore and the soil has started to dry out and so has the garden, because the sensor continues to report 100% humidity skipping the irrigation cycle. How can I unlock the sensor humidity reading?

Why do my zones only activate for 2 seconds?

Hello, I have 5 sprite-type irrigation controller units installed. In one of them, the irrigation stops after approximately 14 seconds on all channels, although it still appears as watering in the status. We have measured the electrical resistance and it is normal.

Perché nonostante l umidità rilevata dal sensore sia superiore alla soglia impostata, la centralina programma delle irrigazioni?

I have a zone that Is not coming on.  I hear the pump going but the zone is not watering at all.  This has been since I first hooked up the system 3 wks ago. 

I had consistent rain yesterday and today and foreseen by smart watering but it still announces watering tomorrow!!?? Why? Attach screenshot

hi,

I put whisperer in a garden pot, after a few days I noticed that it indicated that the soil was moist even if it was not.
it was particularly dry.
two days ago I moved it, I made the calibration and zeroed the self-learning but still today it shows me that the soil is moist while the soil in the pot is now particularly dry, it is necessary to irrigate!
indicates that it is 98% wet.

what is wrong?

and while because from the app I only see humidity of the top soil while from the web with the webui I also see the humidity of the subsoil?

tnks

best regards

stefano

Good afternoon. 

 I have problems because I don't recognize the wifi.  I'll explain. First I connect by wifi to netro and it does not give me any problems.  But when I go back to the next screen to connect the mobile to the wifi and the wifi from home no longer appears. He's gone. And I can't continue with the installation.

Regards

I have a Sprite installed at a healing garden--part of a new transitional home here in Sebastopol, CA  for homeless veterans on which I was the project manager.  However the non-profit team who will bring in the vets has not taken occupancy yet and the wifi will be theirs.  It says in the netro installation that in case of no wifi , it "might work to use the "test run" program on your iphone on the log-in page.  But I cannot see the "Test Run" option  on my iPhone 6S.  

Please help because with the corona virus shut down, Netro is closed and  it could be weeks before I can get to the site to water it manually and all the plants could perish for lack or water!!!

Thanks for any help,  Yohan Morgan.  707/332-3050, USA  cell. 

This is my set up.

I have a netro device + whisperers 

I have set up the netro to skip the previous day and the next day after raining.

I also have set up the schedule for watering from 6 am to 7 am.

If moisture is above 50%, then watering is skipped.

Yesterday it rained a lot and today all the zones were supposed to be skipped. But one of the zones went down to 45% of moisture and watering was started at 19:22.

1) why this happened?

2) Can I change the moisture level to a lower one? Current limit in the application is 50%