Hi there

I have read this article explains how to save water based on 

- seed type

- watering adjustement - EPA

- how tall to cut the grass

- how tall to leave the grass to growth ( deeper roots, the problem of loosing water by transpiration)

https://zulueta.com/regar-el-cesped-como-ahorrar-el-50-de-agua/

Currently the whisperer takes into consideration soil evaporation, but I do not know if transpiration is something to add to the watering algorithm

Is it possible to change the order in which the garden zones are shown in the Netro App?

In my case they are shown in the same order they were created initially in the app and I would like to see them in a different way.

I suppose I could delete them and create everything again from scratch, but I would like to avoid that.

I have an existing 18 zones irrigation controller which I am replacing. I require 2 controllers. No master valve or pump.

It is possible to connect both commons to the existing common connected to the 18 zones?

Thanks 

Hi there :)

I want to set-up a watering duration for my desert garden (Phoenix, AZ). We should water our garden deeply and infrequently. So, I want to set-up a watering time of two hours. Unfortunately, the app has a maximum duration set to 60 minutes only. Any suggestions?

Thanks. 

Hi I have had to send back my spark due to a problem with one zone not operating, I’m now trying to do a reset on my whisper, I have pressed the power button quickly 6 times, on numerous occasions and cannot get it to reset, any help would be much appreciated. New Spark arrived and working well, l just can’t seem to reset the Whisper no matter how many times I try the on/off 3 times. Are there any other action I could do or do I return it for a replacement?

Good morning.
I just started using Netro Sprite 8 zones out of 12 zones with two whisperers.
Congratulations for the App and the Web interface I'm using.
I have a concern about some trivial errors in the interfaces:
If you go to settings/preferences/SchedulingSetting
1.1 The Italian translation of "Two Frames" in "Due Cornici" makes me smile, it is better translated in "Due Cicli" or "Due Fasi". But my suggestion is also for English : it is my opinion that if instead of "Time Frames" and "Two Frames" you use "Time Phase" and "Two Phase" it is much better also for English and automatic translations free from misunderstandings.
1.2 Only in the App and not on the Web, the description of the two phases has "afternoon" under "morning" and vice versa.
Now I have a question:
I ask you for an explanation on Smart Scheduling.
I had set a lower limit of 10 C° and a Time Phase of 6:00 - 10:00. When I removed the 10 C° limit, the system did the same day a cycle at 23:58 instead of waiting for 6:00. why?

I hope I have been helpful and thank you for any response.

My sprinkler started although it's raining. How do I turn off the automatic "feature"?

Especias primarias cuales son?

Especias primarias cuales son?

Especias primarias cuales son?

I set up all of my zones for smart watering today and it looks like it will be running all day. On zone 1 it must have watered 5 times (close to an hour total) even after it showed 100% saturation. Do i need to adjust some settings? That is way too much water for 70 degree weather in April. 

Thanks,

Matt

Hi,

The inteligente mode watering a lot of minutes. However I have adjusted the dimensions and type of soil and it seams there is no impact on the schedule. Then I have decided to stop intelligent mode and schedule by myself. However I do not see my schedule in the calendar. I have setup it on preferences but it is not visible. My fear is not active. Thanks

Hello,

I am presently uprgading my jeedom plugin of Netro and I need to test my code with all models. I can do it with Sprite/Spark/Sensor since I have got the devices in my own installation. This is not the case for Pixie, I do not plan to purchase it since I do not need it but some of my plugin users do have it.

Do you have a test/dummy serial number that I could use for testing Pixie integration ?

Thanks

How do I set the Sprite for two users. Setting up user 1 killed the user 2 setup.

Norm

Hello I have 4 pixie devices.  Two are right next to each other.  One of these two keeps going off-line every couple of days.  Then i have to manually press the button on the device to bring it back on-line?  How do i fix this annoying issue?  Thanks. Sang

Hi there - trying to add a manager into the app and I get "Network Error with code: 3405"... I am sitting next to my network and the Netro Device 

Hello, I need help to change the settings from Fahrenheit to Celsius in the app, I have a smart plant sensor.  Thank you

Hola,

Cuando estoy configurando las zonas me pide un valor de area, ¿en qué medida? ¿Metros cuadrados?

Gracias

good evening, I have 4 valves connected under relay and 3 direct, the 3 direct valves work correctly but on the first 4 I always get an E2 error. is it possible to disable the open valve control?

I swapped out a Hunter ProC controller with a Netro Spark 16 zone controller  The zones all work fine, but the pressure is now too low   When I ran a valve test all of the zones were normal but I had an error message for the Master that says “open circuit”   Not sure what it means or how to resolve it   I checked the wiring connections and they seem fine. Has anyone else run into this ? Thanks 

Neil