I am still trying to figure out the rain prediction algorithm. 

I had 1 set of zones schedule to eater at 5 am on the 17th.

This was overridden by the program anticipating rain at 3am on the 18th (according to forcast). Why does it look so far ahead? Does it take into account the current moisture reading? There is an 85° full sun day between these events.

Hi, I need to use Only my programs but I cant turn off Smart control. So the app starts to water even When I dont want to. 

I recreantly purchased the netro controller and several times it has gone offline with having to unplug and restart. This seems to only work for a day and then goes offline again. I have rebooted my rooter which is on the same floor as the netro. Any help would be great.

Hello,

My Netro Sprite Is linked with the Google assistant and Google home app. I can see Netro in both apps but for some reason Google doesn’t accept any voice command or type commands. I tried many times resetting and reinstalling apps still doesn’t work,please help

Can I tell the smart watering app that it does not appear enough water is being applied to certain zones?

How can I get the app to generate a new watering schedule

Is it possible to create a program that ignores the data from the whisper sensors? When its above 90, I like to run a 3 minute session on all zones to cool the blades off, but if the moisture is too high it skips those zones. I'm fine with my other programs skipping since they're more about the soil. 

Hallo,

In der app sollte es möglich sein den richtigen niederschlag auch auf 0mm stellen zu können.

Zurzeit ist nur 1 mm möglich

I have a smart zone comprising rotor heads.  As I understand, rotor heads need to be run for longer times than other types of heads because they are only delivering water to one direction at a time (the current direction of the stream of water from the rotor).  Further, the amount of water delivered in a given time depends on how large of an arc the rotor passes through.  For example, if the rotor sweeps through only 180 degrees for 10 minutes, that ground gets 2x the water per unit area than if it runs through 360 degrees for the same 10 min.

So, it seems that, since the choice of rotor head does not include information about the arc it will travel through, there is no way for the smart watering algorithm to know how much water is being delivered per unit area, i.e. a zone with rotors going all 360 degrees is likely under-watering.

I believe this is happening on my lawn, and i would like to make a change in order to increase the time of watering for this zone.

What dials do I have at my disposal to make the smart watering algorithm water this zone for a longer period of time?

Today I see .40 for rain but yard still got irrigated. The smart water is set for .20 and to skip today, previous, tomorrow. Also set for expectation. Am I missing something? 

Hi

How I can reset whisper sensor

Like hard reset

I got one reporting 129 c temperature 

Of course it’s hot outside but

Not like that 

I have three whisper sensors,  all of them  but one is reporting moisture levels.  Temperature and sunlight are correct, but moisture is 0%.. I have reset the self learning, Did a hard reboot, and  Reattached the sensor to a different wireless network.  What else can be done?

I added the sensor as a stand alone, then added it to a pixie. Now I can’t figure out how to delete the whisper from the drop down screen. I go into settings and there are no sensors to choose from. Screenshots attached.

I have 8 pixie faucet timers and 4 whisper sensors:

3 for backyard

3 for front yard

1 for drip irrigation in front

1 for drip irrigation in back

I’m trying to assign the 3 front timers in a single zone and sync with 1 whisper sensor. So far, the sensor only seems to sync with 1 timer and each timer shows up as a separate zone.

Also want the same for the back yard. Is this possible?

Can pixie timers be used to create zones?

One of my whisperers gives a zero reading on all metrics about twice every 24hours. Other times it seems normal. Is it broken?

I have a front yard with zoysia grass, about a thousand square feet, no trees. My app keeps telling me that it will water this grass tomorrow. It is obvious that it needs watering, but the next morning I see that it has not been watered and it says I will water it tomorrow. There is no rain forecast, it has been very hot. It Waters the rest of my yard properly, it's just my front yard that it does it like this. Why does it keep changing its mind?

Also this same area, my front yard, has no trees but the app says there are trees on it. And I cannot change it. I would think if this area had trees on it it would be taking much more water and the app would water more. How can I change this on the app?

Is there any way to increase the font size on the rain and irrigation charts in the app.  Alternatively can the data be switched to a table with larger type?   Or zoom?

I am having difficulty setting up my timer.  I have Netro connections, but I can not seem to make my phone connect to schedule a time for irrigation.  manual does not have good information on trouble shooting this issue...

I need help with that.

I signed up to be a beta tester but have never received any information or a beta version of the app to test out. Anyone actually beta testing anything?  Maybe I just wasn’t chosen to participate.   

Can I use my app to set up another device that will be on a different WiFi? It is for my Mother’s lawn and I would like to get it set up using my phone