Hi Team,

I've setup my controller to skip 2 days water if more than 10 mm rainfall is reported.

I have local weather station: https://www.pwsweather.com/station/pws/KADAECOWITT

Which is reported 32 mm, smart zones are enabled , but controller won't skip for 2 days.

Could you please ?

Controller SN: 0cb815314670

Regards, Zsolt

Hello,

After the winter only one of my three sensors shows in the app.  (Twisty Baby Locust).  The other two do not, and when trying to add back in the app errors out as they are already associated with my account....how do I find them and get them back?  I have charges both to ensure good power, and waited multiple day for them to sync, but still missing.

Thanks

Dan

Hello,

Zone 4 out of my nine zones will only run when I manually  turn the  controller valve  in the box in the ground, and not from my metro sprite app. I tried removing and inserting the zone 4 wire in the Netro slot , but still no luck . All the other zones will run from the app except zone 4. Please help.

Hi,

My Whisperer 1 doesn’t show any signs of life after two weeks in bright sunlight.

I’m pretty sure the battery or charging circuit is dead after no use for over a year.

Do you offer a repair service or replacement battery?

Regards,

Andy Fiore

I have 2 zone in full sun with hydrangea and Japanese maples. I need to increase the length of watering time on the automatic watering cycle and the frequency

Hello,

I get this error only on a couple of zones.  See the attached photo. As you can see the zone "misc" shows error.  Any ideas 

I have a Netto controller 12 

It starts the water pump but not opening any valve 

It would be great if for someone like me there would be an option that unifies multiple controllers into just one home so that scheduling would be much easier and avoids multiple zones of different controllers run at the same time. When programming controllers in fact, I have to keep switching programming in various controllers to see if that time is not taken by another zone of another controller. Otherwise water pressure would be a problem if two or more zone are running at the same time in different controllers. 

Hi everyone,

I tried to conect 24v and 9v  valve to ny Netro 6 zone system. It seems dont work... I heard a noise near evry valve when turnd on (on manual mode) but water doesn't com up... Just a 9v valve can open just for few second... Water comes up... But after this tine... Water stop to come.

In the pictures show a 2 model used (24 and 9v)

Thanks to every can help me

We have 3 controllers for over 24 zones. 

Dark mode and font size (especially a problem with charts) are two things that were going to be addressed a few years ago. Could I please get a current status on when dark mode will be available and when font size, or at least the ability to zoom the app screen will be available? Turning on the Apple magnifier, or having to take a screenshot and then zoom that so that you can read data is very inconvenient. 

Question in subject title

I have installed a new Sprite - however, I have 3 common wires but only two slots - and only one wire fits in each slot...

Hi there I use the netro smart feature and the whisperer. 

The smart schedule for zone 5 watered 28 minutes at 5am and the sensor measured 99% humidity.  Then it watered again at 6am... which is obviously a waste of water as the zone is already 100% humid. So it look like when the program starts it does not take into account the humidity again until the next run for that zone. 

For zone 5 I am using regular mode. Not the Deep or EPA. 

I also have the condition that 

- Sensor to report every hour

- skip watering if above 60%

- Sensor firmware 2.0.1

Can I send my controller in to get it repaired? 

Dear Fellows,

I will be away for over a month and want to confirm the best practices to ensure my Netro Stream batter operates reliably throughout this period. Could you provide tailored recommendations based on my device’s current configuration and usage?

Device Details:

• Hardware : Netro Stream 1.0
• Firmware: 1.0.0

Please advise on any critical steps I might have overlooked. I aim to finalize my plans.

Thank you for your assistance!

Best regards,
Kelvin

Hi

Suggestion:

It would be great if it was possible to have a better overview in the Netro app when using multiple controllers. 

For instance, we have 2x Spike 6 zone controllers and 1x Pixie in our setup and it's currently tricky to have a overview over all zones scheduled in these controllers without switching back and forth between them. If only Schedule tab would list all our zones setup in all our controllers :-)

Anyone else have problems with whisperer/whisperer 2? The ones I have just seem to stop working out the blue.  The current problem unit is a whisperer 2 which was sent to replace a broken whisperer.  It comes on, lights up, and shows 100% charged when plugged into a usb power source.  As soon as I unhook the power source it stops working, and oower button does nothing.

I have a digital water metering in my house from my water supplier. So know the exact amount of water that ist running for all zones If netro ist running and watering the Garden. Unfortenately i can Not find an Option, to Tell netro how much water in qm per hour is running for wach zone. IT would be great If that could be implementated to have an exact number of qm water that ist uswd for watering each zone. So gar I know netro gives only an wstamated number of water used for wach zone, depwnding in size of watering area and Type of watering equipment.

Sprite-12

I want to utilize automated rain delay feature.

If I have my 11 zones enabled for Smart Zone watering, the zones will water in a random order.

I need them to remaian in order 1-11. I cannot yet find a readon why.

Not much fun sitting on my lawn when a zone unexpectedly turns on.

If I use a manual program, then the rain delay feature cannot be used.

Is there a way to enable an automated rain delay in a manual program?

and/or

run the zones in an order when utilizing the Smart Zones?

And yes, most of my zones have the same environment settings