Anyone else have problems with whisperer/whisperer 2? The ones I have just seem to stop working out the blue.  The current problem unit is a whisperer 2 which was sent to replace a broken whisperer.  It comes on, lights up, and shows 100% charged when plugged into a usb power source.  As soon as I unhook the power source it stops working, and oower button does nothing.

How do I change and save schedule? 

I have installed a new Sprite - however, I have 3 common wires but only two slots - and only one wire fits in each slot...

Hi

Suggestion:

It would be great if it was possible to have a better overview in the Netro app when using multiple controllers. 

For instance, we have 2x Spike 6 zone controllers and 1x Pixie in our setup and it's currently tricky to have a overview over all zones scheduled in these controllers without switching back and forth between them. If only Schedule tab would list all our zones setup in all our controllers :-)

Dear Fellows,

I will be away for over a month and want to confirm the best practices to ensure my Netro Stream batter operates reliably throughout this period. Could you provide tailored recommendations based on my device’s current configuration and usage?

Device Details:

• Hardware : Netro Stream 1.0
• Firmware: 1.0.0

Please advise on any critical steps I might have overlooked. I aim to finalize my plans.

Thank you for your assistance!

Best regards,
Kelvin

Can I send my controller in to get it repaired? 

Hi there I use the netro smart feature and the whisperer. 

The smart schedule for zone 5 watered 28 minutes at 5am and the sensor measured 99% humidity.  Then it watered again at 6am... which is obviously a waste of water as the zone is already 100% humid. So it look like when the program starts it does not take into account the humidity again until the next run for that zone. 

For zone 5 I am using regular mode. Not the Deep or EPA. 

I also have the condition that 

- Sensor to report every hour

- skip watering if above 60%

- Sensor firmware 2.0.1

Hi,

why after irrigation the humidity is lower than before?

This problem only with 2nd gen sensor...

Thanks

My controller has been out almost a month. I have factory reset, short reset uninstalled app, and unplugged it. No matter what I do, i cannot get past the connect to netro wifi step. I need to blow out my sprinklers and I cannot get my device to work to manually run them. It will say its connected and do the spinning wait thing, then suddenly tell me to connect to the netro internet again. When I go to do it again it says no internet connection. Please help me. I sent an email from my email as the registered user (husband) is deployed in the middle east. Please look for an email from "kimbo__@" 

Thanks!

How do I get a manual run without having a delay. Manual should be manual in my opinion. No added delays from his knows where. Please can anyone help?

I have a Sprite which has 5 working zones which are all connected to smart watering, 4 to sections of the lawn and 1 for the garden.  The lawn zones all water automatically but the garden zone only waters manually.  All zones have been set to water automatically via smart watering.

What could be the possible cause of this please.

Help! How do I set up my controller to a connect to my new router?

Vincent Devlahovich 

805-813-1216

Loyal customer

Am I able to create a schedule for new seed that allows me to add 2 watering times (1 in the AM and 1 in the PM)? Right now I had the create 2 separate schedules. 

I have 6 zones and all but zone 1 run.  I start running manually and app says watering but nothing.  I checked the wires, none loose.  It will run randomly but I’m getting really frustrated.  

Hi everyone!

My Whisperer Smart Plant Sensor has broken. I would like to know if it is possible to fix it by buying a replacement part or if there is a DIY solution to reuse the device.

Thank you.

Hello,
I have two irrigation lines on the same garden, is there any setting that would allow these two areas to be “tied together” such that they irrigate on the same day (session)? (Obviously first one line and then the other).
Thanks

Desde hace unos días la APP no está funcionando. Según la APP el WiFi está OFFLINE, pero según la página web está ONLINE. Según ambos está WATERING pero la realidad es que no está regando y no responde a órdenes. No dispongo en este momento de acceso físico al dispositivo. ¿Podrían indicarme si el problema es un problema local o de la APP/Web?

Why is connection lost with my cover on. But when I take it off it then reconnects? My lawn once again looks like crap because this thing glitches out.

Hello there!

I'm really hoping you can help me. I bought two Whisperer 2s.

My sensor shows the moisture way above where I have my watering adjustment set to not water, but it is still watering. What am I doing wrong?