My New Whisperer 2, after worthing fine for 2 days connected in the garden, now doesn't switch on any more, even after USB charging (showing full charge green light near the USB socket). It's offline and nothing happens when pushing the power button once, for 3, 5, 10, 25, 30 seconds.

What do you think ?

What should I do? Water is leaking out of my zone 5 only when they aren’t being used creating giant puddles in my yard. Any help?

Where to see Whisperer data collected in the Netro ?

When I put a fully charged battery in the timer, the white light comes on. I press the button to try to link with the WIFI router, nothing happens. I never see a white flashing light. If I press the button again a steady red light comes on. I have another Pixie and it links quickly with the router and works well so I know the WIFI router is working well but it never sees the water timer that is not working. 

How do I lengthen the duration from 60 minutes to longer

Hi there 

I would like to know what kind of sprinkler I have to set up in the app if I am using Rainbird R Van rotator 

irrigation programs don't stop. even if the timer stops, the water continues to flow out. even if active in manual mode, I can't stop the water flow.

Has anyone had only one zone not work properly? I've checked my voltages and everything seems to be normal but one of my 4 zones does not operate either with the schedule or manually running the zone. Any tips help cause i'm at a complete loss.

Thanks in advance

Boyce 

Ho un sensore che funziona male, non legge la temperatura e la lettura del umidità è un altalena.

Come posso risolvere? Inoltre rileva umidità 25% e sta piovendo abbondantemente da più di 2 ore.

How do I setup the Netro to only check for rain and skip the rainy days ?  I don’t want it to enable smart watering and change my watering schedule but I would like it to detect and skip rainy days.  Thanks!

Hi,

My Netro-12 is currently running 5 zones at the same time when it was mannually turned on to go each zone at a time, also, the back end of the zones (6-12) does not respond to the app commands and whenever the app said the zones were turned on, it was still the first five zones that were running.

How close does this pixie z1 faucet timer have to be to the hub because it’s approximately 21 ft from it…

WiFi connected

Hub light is solid green

And the timer is offline

Won’t stay connected

Hi 

I just restarted my irrigation system after the winter.  I have tried to manually run a zone.  After watering for 5-10 mins the water turns off but the Netro timer still shows watering.

I am trying to determine whether the pump has turned off because the Netro "on" signal stopped or whether the thermal overload relay on the pump circuit caused it to shut off.  

Is there a way I can check which it may be?

Thanks

Vardhan

I have a broken irrigation and would like to turn off that one station until I fix it.  How do I do that?

Hi there. How can I program specific zones to water twice in one day?

Hi 

I am getting an error in the app like " Invalid group ID 39654: invalid device status "

What would be the reason.  Also I am unbale to pair my device.

Please advise on this.

Thanks 

Ashok.

I have three zones that are running at the same time with low water pressure to all three. This is a new problem. Any ideas on hat might be causing it? 

So far I've tried replacing one solenoid, that did not work. I switched the zones in the control box for one of the three zones but the same result when I activated the switched zone. 

I also tried disconnecting one of the zones, and when I triggered it it did not run. But when I triggered one of the zones I left connected, it did run with low water pressure

Hi gents 

I have setup a new up to 12 zones metro  replacing an 8 zone hunter system.

So far only 5 zones are active

I am missing something small

Hunter old wiring attached 

Thanks! 

First of all, I have been using my Sprite for one year, and the result is very positive. My lawn is better, and I have learnt about how watering should be done in my case. Congratulations to the Netro team. Let me add some questions below.

On 2023-06-13 Wency said "Netro sever side gets/ updates weather information every early morning at around 4 am.

If the weather forecast changes, Netro will update and recalculate the schedule." But could you expand what time zone is this 4 am?.

And a second question is: how often the system recalculates the watering scheduling after a programmed or manual watering? Will that go in the same refreshing as the weather info refreshing? also at 4 am?

Thank you.

Good morning. I am observing that when I manual-water using the web app, and the watering ends, the indicator (blue watering can) remains blue, indicating that the system is still watering. Only resets when the page is left or refreshed. I think that the refreshing should be done automatically, perhaps. The current situation makes the user think there is some hang up in the system, although it is not operationally significant.

Thank you.