I removed an older controller and replicated the wiring when installing the new Netro.  Everything appears to be correct?  However, when watering is activated, the valves will fill up and vibrate or what not with water rushing internally.  But the sprinkler heads don’t pop up and no water comes out.  Any help here would be greatly appreciated.  Thanks!

How can I set the Netro up to  water only on two specific days - the same days each week?

Hi,

I have a whisperer that monitors zones 1, 2, and 3.  Zone 1 is the primary zone.  Because whisperer detected a moisture level that was too low it did an additional watering of 10 minutes.  The strange thing about it is that it only watered zone 1 for the additional 10 minutes.  Why didn't it water zone 2 and 3 when they have the exact same conditions and moisture levels.  I had to go in and do a manual run to even out zones 2 and 3 with zone 1.  

Also in the beta software when you try to switch from basic to advance watering or choose a different watering algorithm you get an error message.  

I really only use Netro to be triggered by IFTTT.  I know it's in Beta but has anyone had success with it?  Mine seems to resort back to syncing evey hour..

For some reason my controller goes offline every once in a while. It messed things up because it shows all of my zones are underwatered when I’m reality they have been watered. Is there a way to switch it from one with network to a different one that is closer. I can’t seem to find how to update the wireless network for the controller

Why is not possible two valves operating at the same time if the pump can be operate correctly?

Hi, I've been trying to integrate Netro with Google Home. The Pixie is connected in my Netro app. After logging into through Netro through my Google Home app. The following message appears:

No devices were found in your Netro account.

What is the issue?

I am putting down some new sod Thursday.  My last controller had a new lawn setting that ran for 15 minutes four or five times during the day.  Is there a way to set that up with this controller/program? I think I'm running a sprite, netro version 2.5.3

Hi, I’m moving and leaving our Netro system at our old house. I just need to know if it will continue to water when I cancel the internet service for that house?

I just find it alittle ridiculous to pay an internet bill for only the sprinkler system to run.

I have 6 Watering zones. I have my weekly watering scheduled to run zones 1-5, never 6. For some reason it is skipping over zones 1-4 and only executing zone 5. I just deleted the whole program and started over to see if that fixes the issue. Does anybody know why this might be happening?  All zones work fine if individually run. 

Netro Whisperer sensor throws misleading and confusing data.

How do I add the Whisperer sensor as a sensor with my existing Pixie? It let me add it as a new device but when I go into my Pixie, the option to pick a sensor is blank.

How to delete all zones and start over

I had a malfunction in one of my valves and one zone watered all night, without metro knowing. That zone is well watered but metro thinks it needs watered. If I turn it off the program it just makes matters worse. How do I get the hydration level back up in one zone without turning off water to my sprinkler system? I still need to water other zones. I need to adjust the hydration level of one zone. Let me know. Thanks

I see that the application always open by default using the plant sensors view. I don't have any sensor and always have to change the view before managing zones and watering schedules. Is there any way to make this the default when opening instead of the sensors? It's really annoying to have the wrong screen everything we open the application. 

I was told by support a few months ago that notifications will be included in the next release of the netro application.

I was included as a beta tester for the new version but I don't see any option for notifications when the system start or stop watering the zones. 

It was or wasn't included? 

If there is an internet outage for several days, does the Netro smart watering device go to a default program or will it stop all watering? 

Having trouble connecting when adding product.

I get to set 3 set up wifi

I connect to netro unit. I cannot switch back to netro app. When I restart app, it wants me to connect to home WiFi..

....

Never ending cycle. Thoughts??

TIA

I am trying to manually torn on the sprinklers and it no longer works. I have used it once, right after I bought it and it has rained for two weeks and didn’t have to use it but now I do. 

It seems if there is any chance of rain, the smart watering always skips the day. Even if I increase the threshold to the highest setting for both forecast or expectation it will skip the day. Can someone help me properly configure the smart watering feature?  This Saturday, it's expected to rain less than my threshold in the evening, I would like the smart watering to water in the morning. 

Thanks