More filters

PIXIE-1 Low pressure IN - gravity irrigation systems don't Work

Leandro
Updated at 2023-08-31 10:48:12 UTC 
HI Support Team and All,

I purchased the smart valve (PIXIE-1)  and the sensor (WHISPERER-2) for my vegetable garden, but unfortunately the pixie-1 releases a few drops of water when it is in irrigation mode, my watering system is ecological, I collect rainwater, 

because the pixie-1 does not it passes water with little pressure, the pressure is low but sufficient for irrigation.

This wasn't written anywhere.

Is it possible to configure the valve to use it with low pressure?
thank you all

Leandro

View: 960   Answer: 2

Zones water at for a small amount of time.

Jacob Matheny
Updated at 2023-09-01 13:44:37 UTC 
I’m currently using my Netro spark 16 to water a 1 1/2 acre field of grass. There are a couple zones that are repeatedly watering for just a few seconds or a couple minutes when they are supposed to be watering for 6 to 10 minutes. It is causing a very big issue in the field. There are a large bare spots that are directly around the problematic zones. Is there any fix to this? I need answers ASAP.
View: 920   Answer: 1

Watering by moisture level higher 90%

C He
Updated at 2023-09-04 06:22:44 UTC 

Hi, 


Netro will water my garten when the Whisperer sensors show 92% moisture level. 


This is smart watering? 


I think, there is no water needed or I’m wrong?




View: 917   Answer: 1

smart watering

Diane Fetherolf
Updated at 2023-09-04 22:29:30 UTC 
How do I turn off smarr wartering?
View: 861   Answer: 1

Parallel Run of watering

C He
Updated at 2023-09-08 08:39:13 UTC 

Hallo and short question: 


I can not find any option to water more than one zone in the same time. Ist this not possible? 


@Netro team: in case the feature is not available at the moment i would appreciate your development 

View: 936   Answer: 2

Arghhh, so horrible

Jake Tanner
Updated at 2023-09-09 16:24:29 UTC 
Need manual run to be immediate... obviously. What prevents this?how to overcome.akes trouble shooting horrible 
View: 891   Answer: 1

Whisperer stake cracked

Carolyn Seyfried
Updated at 2023-09-09 20:22:46 UTC 
Whisperer stake cracked when lawnmower hit it. Can it be fixed?
View: 921   Answer: 1

Soil moisture adjustment

Kyle Giacomini
Updated at 2023-09-12 01:34:23 UTC 
Is there a way to manually adjust the soil moisture levels? For example, I have a zone that is reading as saturated (above 80). However the irrigation in that zone has not been connected prior. It would be useful in the app to be have the user adjust soil moisture levels manually to help with issues like this in the future. I do not have any soil moisture probes installed so the moisture levels are being automaticaly calculated by the smart watering algorithm. 
View: 956   Answer: 1

Scheduling Issue

Steve Loesch
Updated at 2023-09-12 13:59:31 UTC 

Hello I have two questions that I hope someone can help with.

First.

I have my schedule set to skip Rain on Previous Day, Rainy Day, Next Day. It just rained for two days here locally and the system still kicked on today. Am I missing a setting?


Second.

When I set my schedule it will only populate for the current month even though I set the program I have for 5 months. Am I missing a setting?


Thank you. 

View: 886   Answer: 1

Change Wifi problem

Luciani Daniele
Updated at 2023-09-12 15:54:28 UTC 
I replaced the router, the extender remained unchanged.  Unfortunately I am unable to reconnect the 6-channel control panel.  It's like it doesn't reset.  After the reset the LED remains off.  The wifi network is present, but it gives me an error when connecting after entering the password.  How to solve 🙏 
View: 895   Answer: 1

smart zone advanced range

Leandro
Updated at 2023-09-12 17:37:36 UTC 
in the SMART Advanced zones section of the APP in the SI system the mm/hour scale goes from 10 to 100
in the US system Cubic inch per hour [in³/h] from 0.1 to 5

the data refers to the single zone therefore VALVE in my case PIXIE 1. 
The scale of values used does not seem to be correct a 3/4 hose with a pressure of 1 Bar brings about 9000 liters per hour 
perhaps the data in the app and mm³/seconds and in³/second I'm doing something wrong.
Thanks for the reply
Leandro
View: 925   Answer: 1

How to leave a valve open all the time.

David Solis
Updated at 2023-09-14 21:05:39 UTC 

Is there a way to leave a sprinkler valve open all the time? I don't want to make a schedule. I have a valve connected to a motion activated sprinkler. I need that valve open all the time.

Thank you in advance

David

View: 965   Answer: 2

My device is offline

carlos davalos melgar
Updated at 2023-09-17 18:50:32 UTC 
How can I reconnect to Wi-Fi

the controller light is green
I have disconnected it from the network and plugged it back in but it doesn't work
Please i need help
View: 937   Answer: 1

Copy setting to new spark device

John Wright
Updated at 2023-09-17 19:57:29 UTC 
My original netro spark died and I have received a new one.  Is there a way to copy the zone settings from the old to the new
View: 1338   Answer: 1

Stephen CC
Updated at 2023-09-19 08:44:03 UTC 

can somebody explain the two way of rain skipping. forecast and expection. I wanna know how it really worked 


View: 948   Answer: 1

Unrequested watering cycle

Claudio Polacco
Updated at 2023-09-23 07:00:27 UTC 

Hello everybody, maybe someone can help. 

This morning I found the irrigation system on, watering the garden, with no schedule active. More, the master enable/disable switch on the app homepage was set to off.

I'm using manual zone scheduling, not smart watering.

The controller is a Netro Sprite 6 zones, Wifi was on and fully functional. 

Any ideas? Thanks.

Claudio


View: 1046   Answer: 1

Horario

Conchi Herrero
Updated at 2023-09-27 13:00:48 UTC 

Hola, sería posible que en la programación, en la hora de inicio se pudiera elegir la hora y los minutos?

Gracias.

View: 956   Answer: 1

Schedule

Jim Lacy
Updated at 2023-09-28 02:00:48 UTC 
How do I clear out the schedule and start over. 
View: 976   Answer: 1

Does the "smart" behind Netro Sprite & Spark use data from Whisperer?

kamiller42
Updated at 2023-09-29 15:44:58 UTC 
Can a Whisperer be assigned a Sprite zone, and the Sprite use Whisperer's data to optimize the watering schedule?
View: 978   Answer: 1

Whisperer 2 "serial already in used" issue

pridebowl33
Updated at 2023-09-29 16:07:36 UTC 

Hello, 


I have been trying to add back one of my Whisperer 2 sensor and got a message saying that the serial has been already in used. Not sure what to do at this point. I was wondering if someone had encountered the same issue and if there is a solution to fix it.


Thanks

Kevin

View: 1036   Answer: 1