Dear customer,

This issue may be due to your device being offline for an extended period. Simply pressing the reset button on the device may not automatically reconnect it. You will need to use the Netro app to change the Wi-Fi settings.

Thanks,

Netro Support

Dear customer,

Thanks,

Netro Support

Dear customer,

Best regards,

Netro Support

Dear customer,

The primary reason your controller is not functioning is likely due to a wiring issue, rather than incorrect parameter settings. Please check the water valves to ensure the irrigation system is operating correctly.

To investigate further, you can use a multimeter to measure the resistance between the common wire and each zone. Make sure to remove the cables from their slots before testing. A normal reading should be between 20 and 60 ohms. If the reading is less than 10 ohms, there may be a short circuit in the solenoid valve. On the other hand, if the reading exceeds 80 ohms, there could be an open circuit.

Dear customer,

The reason your device is stuck in "connecting" while manually watering is that it went offline on the 29th. We have noticed that your device is now online. However, due to poor network conditions, the manual watering connection may be slow. We recommend setting up a watering schedule so that the device can water automatically, even when it is offline. If you wish to upgrade, please send an email to support@netrohome.com, and our technical team will assist you in upgrading the firmware.

Best regards,

Netro Support

Dear customer,

We have received your email in our support inbox. Netro Customer Service will assist you with this issue. Please check our response.

Thanks,

Netro Support

Dear customer,

We have received your email in our support inbox. Netro Customer Service will assist you with this issue. Please check our response.

Thanks,

Netro Support

Could you please send your request to our support@netrohome.com email? Our technical team will assist you in resolving the issue.

Dear customer,

Thanks,

Netro Support

Dear customer,

Thank,

Netro Support

Could you please send your request to our support@netrohome.com email? Our technical team will assist you in resolving the issue.

Dear customer,

Netro Pixie-1 operating temperature: 32℉ to 122℉ / 0℃ to 50℃. If there are no watering activities during the winter, we recommend drying the device thoroughly and storing it away.

Thanks,

Netro Support

You can guide the new owner through downloading the Netro app and registering a Netro account. Then could you please send your request to our support@netrohome.com email? Our technical team will assist you in resolving the issue.

You can guide the new owner through downloading the Netro app and registering a Netro account. Then could you please send your request to our support@netrohome.com email? Our technical team will assist you in resolving the issue.

Dear customer,

Best regards,

Netro Support

Dear customer,

We noticed that your device is already in setup mode. Could you try pressing and holding the device for 12 seconds, then reconnect it to the network? If you continue to experience issues, please kindly send an email to support@netrohome.com with a detailed description of the problem. We greatly appreciate your understanding and cooperation.

Best regards,

Netro Support

Dear customer,

From your forum post, we understood that you refer to Flume as an external water meter. The scenarios you mentioned typically involve an external water meter, and coordination with local plumbing services is required to modify the pipeline, which is generally done at the pipe connection. Unfortunately, this is not something we can facilitate, as it involves re-routing the plumbing.

Dear customer,

Could you please provide detailed information about which zone to help us identify the sensor device? If possible, please send us an email at support@netrohome.com. Our technical team will be able to assist you with these issues.

Thanks,

Netro Support

Dear customer,

You can use an external multimeter to measure the resistance of the water valve. Before measuring, ensure that the wires connected to the water valve and the common wire are disconnected from the controller. If the resistance is greater than 100 ohms, this indicates an open circuit. Conversely, if the resistance is less than 20 ohms, it indicates a short circuit.

Regards,

Netro Support

Dear customer,

Could you please tell us that you are using the original Netro power supply AC24V? If possible, please send us an email at support@netrohome.com. Our technical will be able to assist you with these issues.

Thanks,

Netro Support