Hello,

My pixie is in standby and does not execute the scheduled programs.

What can I do to change that ?

Thanks 

hi, I have a problem, my Sprite 6 was Offline, I tried to do a quick reset, nothing!  i did a total reset.  After configuration, the white light is on steady, but I don't have the system in my app.  I tried to do the total reset, but the light does not flash and I no longer see the wifi of the Sprite.  what can I do?

But the water is still running, I was testing it with manual and it just says “pending” under manual and never shuts off. There is a check mark on “sleeping” but it obviously is not sleeping.

I got 2 zones of 2 Rainbird 5004plus Rotors irrigating the same 90m2 as water flow was not enough to have the 4 rotor heads working at the same time. As mi experience the automatic programs do not successfully work, I would like to try a more controlled approach in specifying the flow rate in the Smart program. But, what value do I have to put there for each of the 2 zones? I saw on rain birds webpage, the 5004 nozzle 1.5 and 4psi, have a flow rate of 7-8mm/h…but the app does not let me select below the 10mm unfortunately. Can you pleas say what number I have to fill-out for those 2 5004 rotor heads?

As you can see, in the app if I try to adjust my existing restriction to start at 7:05am instead of 7:20am, it will not let me make the change because it says the start time must be before the end time (which it is).

Hi there none of the whisperers are sending data. 

I do not see any data of moisture, sun light, temperature etc.

I have changed to a recurrence of 1 hour to send the data.

Hi...stations Turn on when scheduled but ap does not show when a station is on. Ap does show after the fact that the zone ran but not in real time. I Uninstalled and reinstalled the ap but no change. Any help?

Trying to manually operate Pixie via the Netro app. cannot get out of sleeping mode.   Time/duration field says; “pending”   Never exits that mode.    I tried on/off 10 times as I read in another reply and that did not resolve.   Removing and reinstalling battery unit did not resolve.  Help! 

My Sprite 6 lose connection.... But if i power off end poewr on again  connection is Perfect....

Router signal is 100%

Hi, my app keeps crashing. Reset everything. I think firmware is not uptodate. Thanks for help (ios 15)

Recently, I noticed that whenever my zone 2 starts (whether manually or automatically), zone 3 turns on as well. This is causing the water pressure to be low to the point where neither zone 2 nor zone 3 are properly watered. This is also causing an unnecessary water waste. Would you please assist?

Running beta Netro app.  Why no play button when I choose and enter run times for each zone?  How am I to start watering?  

I ve another problem...... If mybrouter connection goes down sprite begin to blink fast and when My router is on again Sprite do not automatically reconnect, i've to manually shut down and power in again Sprite.... Why? 

I have 2 houses and I wanted if it is possible, with a single phone to control 2 Netro
Cordially

Recientemente instale tres sensores junto a  él programador Netro, pero los sensores no indican ni horas de luz ni humedad, en la app 

¿cuantos días están en modo aprendizaje? 

Muchas gracias  

For new seeding i need possibility to run every zone every hour for 5 minutes…

Smart watering is over watering the yard

I am trying ro add a new device but when i connect to the device wifi so i can configure it the app logs out and i have to switch back. So stuck in a loop unable to add the device

Does anyone know why the Dark Sky weather service was removed and replaced with Netro Weather.  My system has work great until today.  All six zones ran this morning and we had roughly an inch of rain yesterday.  Never had this issue with Dark Sky.