更多篩選條件

Set up weather underground

Giovannini Alex
更新時間 2024-10-05 18:35:32 UTC 
話題: Netro App

Hi,


I can't set ITREVI107 station ID ,of weather underground,as my weather provider,  for sprite 6


Thank you


Alex

瀏覽: 1825   回覆: 1

Sprite wont connect to your internet so I can move forward

cjulian
更新時間 2024-10-05 18:05:09 UTC 

My controller has been out almost a month. I have factory reset, short reset uninstalled app, and unplugged it. No matter what I do, i cannot get past the connect to netro wifi step. I need to blow out my sprinklers and I cannot get my device to work to manually run them. It will say its connected and do the spinning wait thing, then suddenly tell me to connect to the netro internet again. When I go to do it again it says no internet connection. Please help me. I sent an email from my email as the registered user (husband) is deployed in the middle east. Please look for an email from "kimbo__@" 


Thanks!

瀏覽: 1691   回覆: 1

Manual mode without delay

Phil Houghton
更新時間 2024-10-04 23:27:59 UTC 
How do I get a manual run without having a delay. Manual should be manual in my opinion. No added delays from his knows where. Please can anyone help?
瀏覽: 1649   回覆: 1

1 zone not watering

cowlo@xtra.co.nz
更新時間 2024-10-01 01:41:13 UTC 

I have a Sprite which has 5 working zones which are all connected to smart watering, 4 to sections of the lawn and 1 for the garden.  The lawn zones all water automatically but the garden zone only waters manually.  All zones have been set to water automatically via smart watering.

What could be the possible cause of this please.

瀏覽: 1912   回覆: 1

How do I?

Rockhead413
更新時間 2024-10-01 00:08:51 UTC 

Help! How do I set up my controller to a connect to my new router?


Vincent Devlahovich 

805-813-1216

Loyal customer

瀏覽: 1724   回覆: 1

Schedules

jonathansalina
更新時間 2024-09-28 11:11:52 UTC 
話題: Netro App
Am I able to create a schedule for new seed that allows me to add 2 watering times (1 in the AM and 1 in the PM)? Right now I had the create 2 separate schedules. 
瀏覽: 1805   回覆: 1

Zone 1 not watering

11807GFT
更新時間 2024-09-24 23:25:59 UTC 
I have 6 zones and all but zone 1 run.  I start running manually and app says watering but nothing.  I checked the wires, none loose.  It will run randomly but I’m getting really frustrated.  
瀏覽: 1843   回覆: 1

Whisperer says: Sensor XXXX already in your account

Thomas Murphy
更新時間 2024-09-18 12:39:46 UTC 
Hello there!

I'm really hoping you can help me. I bought two Whisperer 2s.


I configured the first one (called Roses 1) and it works perfectly.

I configured the second one (called Office Pot Plant) and it went through the configuration fine but then doesn't appear in my app in the Sensors section (Roses 1 appears, but Office Pot Plant doesn't). 

I tried to configure it again and it told me that the name Office Pot Plant was already taken, but it doesnt show anywhere.

I tried a factory reset on the Whisperer which worked but when I tried to configure it, it gave me the error "ERROR: Sensor XXXX already in your account".  

I've looked at my account on the web and it only shows Roses 1.
So I can't add the device because it says it's there already, and I can't delete it because it doesn't appear!

Please can anyone you help? I wrote to Support yesterday (from the email for this account) but I'm hoping someone has a DIY fix for this?

Thank you so much!
瀏覽: 1879   回覆: 1

Sensor

Kathleen Hamilton
更新時間 2024-09-11 19:43:50 UTC 
話題: Netro App
I have six sensors but use only 3 which are 1, 3 and 4; however, I am having problems with sensors 4.
瀏覽: 1975   回覆: 1

Smart watering not working

Carolyn Seyfried
更新時間 2024-09-10 16:17:51 UTC 
My sensor shows the moisture way above where I have my watering adjustment set to not water, but it is still watering. What am I doing wrong?
瀏覽: 1956   回覆: 1

Broken whisperer sensor

Jesús López
更新時間 2024-09-09 16:19:33 UTC 


Hi everyone!

My Whisperer Smart Plant Sensor has broken. I would like to know if it is possible to fix it by buying a replacement part or if there is a DIY solution to reuse the device.



Thank you.

瀏覽: 2036   回覆: 2

Netro Whisperer humidity error

Pierluigi Cilli
更新時間 2024-09-08 07:29:59 UTC 

Hi,


why after irrigation the humidity is lower than before?

This problem only with 2nd gen sensor...


Thanks

瀏覽: 1965   回覆: 1

Discrepancia APP y WEB

JM del Amo
更新時間 2024-09-07 13:06:53 UTC 
Desde hace unos días la APP no está funcionando. Según la APP el WiFi está OFFLINE, pero según la página web está ONLINE. Según ambos está WATERING pero la realidad es que no está regando y no responde a órdenes. No dispongo en este momento de acceso físico al dispositivo. ¿Podrían indicarme si el problema es un problema local o de la APP/Web?
瀏覽: 1979   回覆: 1

Connection

jackielaith
更新時間 2024-07-21 04:36:32 UTC 
Can't connect to the internet with this app 
瀏覽: 2185   回覆: 1

Problem with irrigation time

Daniel Encinas
更新時間 2024-07-12 10:43:36 UTC 
Hello, I have owned a Netro Sprite programmer for several years.

The problem I have is that it programs the phases intelligently and if it indicates that it has to water for 10 minutes. It only waters for about 1 minute but the app shows that it has watered for 10 minutes. The garden is drying out and I don't know what to do.
This happens to me in all irrigation phases. If I program it manually the same thing happens to me. If I try it twice, the second time it takes even less time to water.
I have connected the transformer directly to the phase, bypassing the programmer, and it works correctly.
Reviewing its problems section, I found a similar one in which it says to look at the 24 volt voltage. (which is correct, around 30 volt) and the resistance in ohms of more than 20 (around 30 ohmios). It also says that there the programmer has a recoverable fuse.

What can I do?


Thanks

瀏覽: 2305   回覆: 1

Bug in Smart watering Algorithm

texan4ever521
更新時間 2024-07-16 18:53:40 UTC 

I would like to know how to get a serious bug in the smart watering algorithm resolved.


I live in north Dallas.  All of our soil is clay.  Most yards (like mine) have Bermuda grass, which is extremely drought tolerant.  This grass grows roots several feet deep and can survive with zero watering for 3 weeks after a downpour that saturates the clay.  (I can show you green grass in a yard that is hard as a rock)  During mid July to mid September the average low is 80 and the high is over 100.  Bermuda grass will go dormant(not dead) if not watered during summer.  You can easily keep the yard looking decent with only 10 minutes of watering per week.


I bought my house in 2020 and it came with a Netro.  After a summer of use, my wife and I failed to look at the auto-pay CC card water bills.  We had accidently spent thousands of dollars on yard watering during the summer. (I can show the water bills)!  (FYI, I had each zone set to the max ECO level)  Instead of buying a new timer, I changed smart-zone to basic instead of advanced and setup very detailed schedules.  


My timer got hit by lightning back in May.  I bought a new one and set it up.  I failed to notice that the default value for new zones is "smart zone enabled with advanced setting".  Even though I had set up manual programs the timer found 'loop holes'.  The advanced mode was watering some zones as much as 70 minutes in 1 WEEK!  (compared to previous 10 min a week).  My water bill went from $160 to $400 ( at least I caught it before it got to $800 again).  


This bug has literally cost me thousands of dollars with a feature that is supposed to be saving me money.  I am not asking for compensation, it was my mistake that that I failed to look at the schedule and CC auto-pay.  


But this bug is ridiculous.  


How do we get the following implemented:

1) Global setting for water conservation (impacts all zones) that limits the max per week and max per month that a zone can be watered 

2) Budgets inside manual programs that will set limits for max per week and max per month.

3) expand frequency for programs to be across 14 days instead of 7 days

4) notifications from app that informs owner of minutes watered per week and per month.

 

Thanks

瀏覽: 2235   回覆: 0

La zona non si spegne

Gmultis
更新時間 2024-07-17 16:29:38 UTC 

Quando collego la valvola la zona resta alimentata a 24 v anche quando finisce il ciclo. Quindi non smette di irrigare anche con la spia di colore verde.

Senza la valvola invece la tensione torna 0 volt.

Cosa può essere il problema

瀏覽: 2279   回覆: 2

Error E1

Simone Ragnolini
更新時間 2024-07-26 11:13:02 UTC 
Ho, we need support, as we are having an issue as the app doesn’t activate watering. The control unot shows E1.
瀏覽: 2182   回覆: 1

Watering system turns on by itself?

Michael Collins
更新時間 2024-07-27 23:34:54 UTC 
話題: 通用

I have the following odd situations:


1. The Netro does not show any watering activity.

2. My watering system is turning on by itself, and one of my zones is just firing away, spreading water for hours on end.

3. The Netro does not seem to be be able to stop it or even show that it's running.

4. Unplugging the Netro did fix the problem. Even more bizarre


I have an old Netro that never did this. I wonder if I should just swap them out?  This newest one seems to bug sometimes?


Any thoughts what could be doing this?

瀏覽: 2229   回覆: 2

Manual watering beta

Lynn johnson
更新時間 2024-07-10 04:17:16 UTC 
話題: Netro App
So I like the idea of being able to manually water when I want especially on really hot days but the battery aftervthe second day dies and never charges more then 10 to 15 percent even in full sun for 10 hours. Would be nice if it charged faster and had a better battery or less drain in that mode.
瀏覽: 2325   回覆: 1