I have a digital water metering in my house from my water supplier. So know the exact amount of water that ist running for all zones If netro ist running and watering the Garden. Unfortenately i can Not find an Option, to Tell netro how much water in qm per hour is running for wach zone. IT would be great If that could be implementated to have an exact number of qm water that ist uswd for watering each zone. So gar I know netro gives only an wstamated number of water used for wach zone, depwnding in size of watering area and Type of watering equipment.

I can't connect both of my two Pixie devices to Alexa — I can only control one.
How can I fix this issue?

Thank you.

Help for my controller dropping the wifi weekly?  I have to unplug the controller to reset and wifi works.  When on vacation my controller can't be unplugged so is there a fix or work around ?

My app on my phone say that the zone is on watering but when i look outside nothing is happening !!!

Hello, I have activated Continuous Monitoring on my Wispering gen2 which means I should get an emediate update when the moister has changed.

But I don't get any update/ change until the aut hourly upate of the measurement is done.

Could you please advise me on how to determine the specific requirements of my rose bush? While I have access to the data, I find it challenging to apply it without knowing the ideal conditions for my particular rose.

Thank you for your help.

Hello,

I get this error only on a couple of zones.  See the attached photo. As you can see the zone "misc" shows error.  Any ideas 

I have a Netto controller 12 

It starts the water pump but not opening any valve 

Hi everyone,

I tried to conect 24v and 9v  valve to ny Netro 6 zone system. It seems dont work... I heard a noise near evry valve when turnd on (on manual mode) but water doesn't com up... Just a 9v valve can open just for few second... Water comes up... But after this tine... Water stop to come.

In the pictures show a 2 model used (24 and 9v)

Thanks to every can help me

Question in subject title

Il programma notturno funziona regolarmente ma non funziona lo start manuale.

Anche entrando nel programma e selezionando esegui ora non parte.

Ho già provato a riavviare App centralina NETRO e router Wifi senza risultato.

Rimane in connessione ma non parte !!

My account Pier1972

Perché nonostante l umidità rilevata dal sensore sia superiore alla soglia impostata, la centralina programma delle irrigazioni?

Hi, 

I have some concerne about the time range. I set the Smart schedule to water just from 5am to 10am. But the Smart program seems to override this control. How can i ensure it would be respected? 

Hello, I have 5 sprite-type irrigation controller units installed. In one of them, the irrigation stops after approximately 14 seconds on all channels, although it still appears as watering in the status. We have measured the electrical resistance and it is normal.

Could you add a pause feature in Manual run? When I am running a zone, sometimes I need to halt the run and make an adjustment or fix a leak and then turn it back on. Right now, I have to stop the manual run and then start all over. 

I have one sensor that is controlling 5 zones, in the last few months it has rained for several days and the humidity recorded has always been 100%. For three weeks however it has not rained anymore and the soil has started to dry out and so has the garden, because the sensor continues to report 100% humidity skipping the irrigation cycle. How can I unlock the sensor humidity reading?

Why do my zones only activate for 2 seconds?

Please

I have had smart cotroller netro for 3 years. Never problems! 

Now i d like to buy z1 pixie with hub! But is it essential the hub for smart controlling? And if yes the hub has to be connected by lan to the router? 

Need to change the rainfall for the prior day, how do I do it? 

I have 3 Whisper gen 2 sensors 2 have firmware 3.1.1 and one has firmware 3.1.5. How do I update the firmware on these devices?