None of the zones are watering when the app says it's watering. I measured each zone when active and each read 28 AC. When testing the resistance, the readings were jumping all over the place for each reading. This is leading me to believe there is an issue with the master solenoid valve. However, there is no wire that connects to the M slot on the controller. Looking around the house for any of the underground boxes, I have not been able to find the master solenoid. Attaching pictures of what I have found. Any help greatly appreciated.

So I like the idea of being able to manually water when I want especially on really hot days but the battery aftervthe second day dies and never charges more then 10 to 15 percent even in full sun for 10 hours. Would be nice if it charged faster and had a better battery or less drain in that mode.

What can I do?

Thanks

My controller has been out almost a month. I have factory reset, short reset uninstalled app, and unplugged it. No matter what I do, i cannot get past the connect to netro wifi step. I need to blow out my sprinklers and I cannot get my device to work to manually run them. It will say its connected and do the spinning wait thing, then suddenly tell me to connect to the netro internet again. When I go to do it again it says no internet connection. Please help me. I sent an email from my email as the registered user (husband) is deployed in the middle east. Please look for an email from "kimbo__@" 

Thanks!

Hi,

why after irrigation the humidity is lower than before?

This problem only with 2nd gen sensor...

Thanks

Hi everyone!

My Whisperer Smart Plant Sensor has broken. I would like to know if it is possible to fix it by buying a replacement part or if there is a DIY solution to reuse the device.

Thank you.

My sensor shows the moisture way above where I have my watering adjustment set to not water, but it is still watering. What am I doing wrong?

I have six sensors but use only 3 which are 1, 3 and 4; however, I am having problems with sensors 4.

Hello there!

I'm really hoping you can help me. I bought two Whisperer 2s.

I have 6 zones and all but zone 1 run.  I start running manually and app says watering but nothing.  I checked the wires, none loose.  It will run randomly but I’m getting really frustrated.  

Am I able to create a schedule for new seed that allows me to add 2 watering times (1 in the AM and 1 in the PM)? Right now I had the create 2 separate schedules. 

Help! How do I set up my controller to a connect to my new router?

Vincent Devlahovich 

805-813-1216

Loyal customer

I have a Sprite which has 5 working zones which are all connected to smart watering, 4 to sections of the lawn and 1 for the garden.  The lawn zones all water automatically but the garden zone only waters manually.  All zones have been set to water automatically via smart watering.

What could be the possible cause of this please.

How do I get a manual run without having a delay. Manual should be manual in my opinion. No added delays from his knows where. Please can anyone help?

Hello,

I had to change my google password and now I lost all my datas from my last installation in my Netro system.

What can I do to find it again. Must I install everything new?

Who can help me?

Thank's

Konrad

I changed the sprinkler head on zone 5 after installing the new controller. All zones work but 5. I can run it manually. It won’t work on smart watering.

Hi,

I have 4 zones and a master valve. When I run any of the zones, they won't shut off when the timer runs out. If I switch the AC power off, then the valve will shut. I have checked the valve and it has no issue with opening and closing except when the sprite is running it. I tested cables for continuity, and I have tried swapping cables with no change. My ac power pack is AC 24v.

This issue affects each of the valves but only when controlled via the sprite. The valves are fully operational otherwise.

Hoping for a fix, otherwise will return to Amazon under warranty and get another brand.

Why is connection lost with my cover on. But when I take it off it then reconnects? My lawn once again looks like crap because this thing glitches out.

How does the Spark test the valves?

I want to connect a 24V input sensor on the spark outlet channels to switch 2 knx connect valves in different location. Cabling to those valves is to long for 24V. 
The valve testing always says that there is not current and switch it off --> Do i need a resistor on the outlet to simulate a valve? If yes, which value should the resistor have?

Thanks,

Peter

Hello

My system has 5 solenoids.  All worked fine until recently.  One will turn on and off manually.  

However in smart timer it turns in but not off.  

How can I confirm if a app set up issue or a hardware issue with solenoid itself.  

Nath