Can I use the Netro Spark 16 if I use the Rainbird ESP Me? I have 15 active zones.

Someone can help me?I need change the day for one program exists...what is the procedure? Thak you

Good morning, I installed a Sprite 6 controller, it works perfectly, but I have three questions: 1. How do I change the irrigation percentage without changing the watering minutes for all the zones each time? 2. When rain or wind is forecast, does the irrigation program still skip even if the smart function is not enabled? 3. When I start a zone in manual mode, for example to control the sprinklers, is it normal for there to be a long delay between pressing the Stop button and the actual interruption? Thanks.

How do I change the wifi network my Netro controller is connected too? I cannot proceed beyond step 2 from the instructions on the app. I get the message "Please connect to Wi-fi network "Netro_IRC_xxx."  However, the app shows that I am already connected!!

Hi, I just bought the whisperer 2 and would like to have it as only sensor for the entire garden, however is allowed to have maximum 3 zones for sensor. Is there a way to link all the zones to it? I have 7 zones.

Thanks

Way Netro had changed my user password?

I'm curious if there is a way to restrict or cap the calculated volume of water used daily for smart watering schedules. For example, my well produces about 3500 gallons a day or close to 4.5 CCF. I have a storage tank where the water is stored. Is there any logic that can be added to the smart watering calculation or scheduling to account for a daily water volume budget? 

I'm experiencing a serious issue with my Netro Spark 16 controller. It connects correctly to Wi-Fi and appears online in the app, but when I try to start irrigation manually, the app just stays on "in communication" and nothing happens.

The problemm is with the 4g Vodafone/HoMobile provider as yout mentioned in https://netrohome.com/en/forum/posts/4052

I have already asked several time the update for the device, but nobody reply me

i wrote also to Netro support email: support@netrohome.com  --> nobody reply me.

What should i do to have this update?

Please

Hi, it’s the end of our watering season where I live, the city just shut off the water for the year. Any guidance on what to do in the app to have the system off for until spring?  

Hi, dopo aver collegato tutto, ho provato a fare un test manuale ma non parte l irrigazione.

Sapete aiutarmi?

Grazie

The app crashea when I click on a zone on Google pixel 8a. I had to configure them with another phone. Already tried to reinstall the app and clear cache

Hey,

Is it possible to individually choose preferences for wind speed on a zone by zone basis? I've got some zones that are connected to sprayers which I would like to keep on a wind speed cutout and but most zones are on drippers which I would like to water independent of the wind speed.

Hi... since it's still fairly warm outside, I'd like to have the Zone water every 2 hrs for about 3 minutes just to keep the ground moisture up.

I'm not clear on how to do this?  Anyone?

I have a hill that was terraced and replanted. I was told to run the circuit twice a day for 15 minutes for a month. Drip lines. Seems like my system doesn’t have that flexibility. Am i correct?

Hi, I can get my Netro controller info using:

curl -v https://api.netrohome.com/npa/v2/info.json?key=MYAPIKEY

(where MYAPIKEY is a key from the user account page)

but when I try to update soil moisture data with:

curl -X POST -H "Accept: application/json" -H 'Content-Type:application/json' -d '{"key":"MYAPIKEY","moisture":100}' "https://api.netrohome.com/npa/v2/set_moisture.json"

I get an error about an invalid key:

{"status":"ERROR","meta":{"time":"2025-11-21T04:54:56","tid":"1763700896_KpmY","version":"2.0","token_limit":0,"token_remaining":0,"last_active":"2025-11-21T04:54:56","token_reset":"2025-11-22T00:00:00"},"errors":[{"code":1,"message":"Invalid key: ","params":{}}]}

What's going on?

I cannot add my pixie z1 to the app because pixie z1 is not shown as an option. I have the hub connected. 

I have programmed my Netro to skip Tuesday’s but the controller waters anyway. How do I stop this?

When I have Whisperers, the system appears to calculate the average over the day about 4 degrees higher than for zones without Whisperers.

It seems that, even though the weather data is available throughout the day, that zones without sensors only use the forecast high and low.

This is insufficient to correctly adjust for the amount of watering required.

For example, today is 7 degrees C up to 36.

Whisperer zones average the temp at 26C while non-Whisperer zone calculate the average at 22C.

On these extremely hot days, the non-whisperer zones are under-watering much more than the Whisperer zones.

Also note that even the zones with Whisperers always under-water and needs custom programs or manual intervention.

This finally explains to me why zones are always under-watered.

Can the system please use multiple day readings for non-Whisperer zones and PLEASE provide more watering?

Hello,

I have 2 Whisperer for automatic regularion of my watering.

They work normally work perfekt but when the bad weather prevents charging for o longer period they go to sleep/closes down.

Then my Netro thinks the soil is dry 0% humidity and aut starts my watering eventhough the soil is 90%.

I have ti disable the Netro to stop watering until the Whispering is charged.

Since I do not get any warning that the Wispering power is too low the aut watering can go on and on wasting my water and flooding my garden!

I have one particular zone that i only require watering for 15 seconds every second day.

How can i do this?  i was able to do it on my previous OpenSprinkler.