Even after several hours in full sun my Whisperer looks dead and does not send any signal.

Shirt or long pushes on the button does not change anything.

I suppose that while not that old I have to buy a new one.

Thanks for your advice

It looks like the sprinklers are not jumping out because of the water pressure is maybe down right after I installed pixie

Raining hard outside for at least 20 minutes but yet, Netro weather n others didn't detect it?

My main water line to the sprinkler system came loose and flooded my vacation home yard with 250,000 gallons of water before the leak was discovered and repaired.  Does Netro have the ability to control an electric valve on this feeder line such that the main valve will only open when the irrigation system calls for water?

Good afternoon.

Sometime my controller lost the connection to the router Wi-Fi for some time ( one day or more) and then it riconnettes automatically. I don’t know why.

This morning it lost the connection , but after 10 hours it was still disconnetter. I tried to re connect it manuali, but the controller didn’t find my router. The router is very closed to the controller. When I connect my phone to the WiFi of the controller, i see “no connection”. So. Ok the controller is off line and I can’t connect it. what can I do? I already try to reset the controller turning of the elettrico power. 

I’m in the Orlando area and on Wednesday I just had hurricane Ian drop over 5” of rain on my lawn. Discover tab shows on Wednesday I had less than .3” of rainfall. I’m using the Netro weather station. Is there something I need to change or update?

I was wondering if there’s a relationship between the weather predicted on the app and the watering frequency. Here it shows daily temperature predicted at 90 degrees when in fact it’s 82 / 83 when 2 watering a week are sufficient. My app wants to water every day and unless I turn it off I don’t see a way to negotiate a more rational and way less costly rhythm. 

I set up my metro system this morning.  I made an error in programming the watering schedule.  How do I reprogram the Smart watering program?  I have been unable to do it.

Also I would like to point out that yesterday at midnight the irrigation started by itself, without having programmed anything, with the app I could not turn off I had to stattare everything through the electrical panel.
As ever this happens, should be a convenience this control unit controlled by the app instead of problems.

Hello, yesterday I mounted the control unit with an electrician, the connections are fine, we tried several times the manual function but it did not work, I am trying in various ways to operate the control unit, after several hours I pressed reset and I managed to start the manual program, now it works but I noticed that it does not start if there is a daily program, is it correct??

Instead the programming does not work on the calendar, I tried in various ways but the irrigation does not start, I think the control unit is faulty, I tried several times to program a minute per sector but nothing works. Now it’s raining here of course I disabled the smart zone so for now only the manual function works, not with programming. What advice can you give me?

Thanks

Rosario

What should my unit light show if it is properly connected?   And where can I find an online owners manual for this product?

Vincent Devlahovich

My netro is using smart schedule. Even though i have ECO on each zone, zones are watering for more than 20 minutes. it rained last night and today morning it was watering for more than 20 minutes.

 How do i change this?

lot of water being wasted. 

Thanks,

Ananth Bandla

Hi!

Tonight at 2.30 my netro start to watering. I had to stop it starting a manual program and stop it because in the app there was no watering sign.

Then I put a restriction for 3 days and around noon netro starts to watering again. There was a lost wifi signal for a minute cause by a voltage drop. 

Is it normal?

Thank you 

It Rains and Netro still watering my plants unless I add daily skips when I see the weather forecast. 

It shows watering, but it is not?

I have an ! inside a yellow triangle showing up on days my sprinklers run. 

What does the ! mean?

My flower gardens have several inches of wood chip mulch covering the soil.  After a season of "Smart Watering" my beds are dry and the perennial plants are stressed.

Does mulch absorb irrigation water intended for the plants?  Is the presence of mulch a factor affecting the duration of an irrigation cycle?

To the Netro community:

We are excited to introduce our new products, the Netro Zigbee Hub and the new smart timer Pixie-Z1. They combined deliver a different experience of smart watering system. 

The Netro Zigbee Hub hosts a long-range local Zigbee network that links all the end devices. It connects to your router (wireless or wired) to transfer data between the end devices and the Netro cloud service. The Hub will work with all our Zigbee products including the new timer Pixie-Z1(introduced below) and the new soil moisture sensor coming this year, as well as the new 4-Zone sprinkler controller and the new weather sensor coming next year.

The new host timer Pixie-Z1 is re-designed from the original Pixie timer in many ways:

1. Always online for instant quick runs. No more sleep mode

2. Powered by two AA alkaline batteries with approximately one year of battery life. Notifications on low battery

3. Supports Google Home and Google Assistant

The Netro Zigbee Hub and Pixie-Z1 are expected to ship in September. To join the Tester program please email to info@netrohome.com and we will send you a discount code in return for feedbacks.

Thanks, 

Netro Inc

I have seen quick stop watering on landing page in app once. Than not anymore. Is this a recent feature? Looks not stable. Meanwhile I cannot see stop button on manual run page where it was before. Shame that everone got wet on garden party.

Hi, I had a Sprite working OK but I needed to move it to another location and WIFI network. I assumed starting from scratch was the easiest method and deleted the controller on the App but now I cant get it back into host mode (<1sec press of reset button) or factory reset it (6-8 sec)....The LED flashes about once every 6 secs or so not every second, no matter what I do. 

So I never see the Netro_IRC wifi network ....

How do I fix this ?

-A