Hello, I am leaving in Italy  have several whisperer devices in my garden and I would like to know if it is better to remove them during the winter season when my watering network is off? Thank you.

I just noticed a yellow triangle with black exclamation mark on one of my zones. Will you please tell me how yo fix this?

Hi, A few months back I purchased 2x Whisperer sensors and paid the shipping from America. However when they arrived a couple of days later and they had been sent from a UK address not from America. I was a bit annoyed at the time knowing I had paid $25 delivery but the were sent from the UK. You currently have an offer on these sensors is it possible to purchase them in the UK yet and claim the discount?

Kind regards

Phil

Can a Whisperer be assigned a Sprite zone, and the Sprite use Whisperer's data to optimize the watering schedule?

Is there a way to leave a sprinkler valve open all the time? I don't want to make a schedule. I have a valve connected to a motion activated sprinkler. I need that valve open all the time.

Thank you in advance

David

in the SMART Advanced zones section of the APP in the SI system the mm/hour scale goes from 10 to 100
in the US system Cubic inch per hour [in³/h] from 0.1 to 5

the data refers to the single zone therefore VALVE in my case PIXIE 1. 

The scale of values used does not seem to be correct a 3/4 hose with a pressure of 1 Bar brings about 9000 liters per hour 

perhaps the data in the app and mm³/seconds and in³/second I'm doing something wrong.
Thanks for the reply

Leandro

Is there a way to manually adjust the soil moisture levels? For example, I have a zone that is reading as saturated (above 80). However the irrigation in that zone has not been connected prior. It would be useful in the app to be have the user adjust soil moisture levels manually to help with issues like this in the future. I do not have any soil moisture probes installed so the moisture levels are being automaticaly calculated by the smart watering algorithm. 

This would be a supper nice feature to add to NETRO. 

Combining with the whisperers

https://irrigreen.com/

Hallo and short question: 

I can not find any option to water more than one zone in the same time. Ist this not possible? 

@Netro team: in case the feature is not available at the moment i would appreciate your development 

Hi, 

Netro will water my garten when the Whisperer sensors show 92% moisture level. 

This is smart watering? 

I think, there is no water needed or I’m wrong?

Hello Netro Support, 

The Spark startet watering today at 4 am as it was calculated by whisperer and weather. 3 Zones got water, but instead of watering 10 minutes the gras got 3 hours water. 

I wasted a lot of water, this is far away of smart watering. My old installation from Gardena / Husquarna never had such problem. 

The spark was not able to close the Ventils! 

The only way was the make the spark powerless. 

What’s wrong? 

Again: the test procedure of the ventiles works without any problem, spark open AND CLOSE every ventile step by step! 

 

Is there any reason for which Moisture to skip watering cannot be less than 50% ? 

Netro Support Team,

Where do I find the calendar view?    Is it the schedule icon on the bottom of the home screen?

I simply want to view when my sprinklers will run in the future when using "smart watering", "level: advanced".

I find that trying to find answers to questions when I am limited to community postings is cumbersome.   A good detailed manual would be very beneficial.

John Kollehner

Houston, Texas

Netro started watering my lawn this evening despite havng four (4") inches of rain all day today! I thought Netro has the mechanism andthe technology to detect rainfall and stops watering when there is heavy rain!?

Hi, I installed the Sprite Netro today. Did a manual test. 

All zones worked fine except one of the zones started running but is not stopping. App shows stopped but the water keep going. 

Any ideas? Is it the metro issue or sprinkler valves? I powered off the Netro but still the water keeps on going.

Hi, I can't associate my netro with the IROVAT1 weather station, the system issues "please enter a station ID" error. What to do? Thank you

Looking in the Personalized watering mode of Smart watering, I would ask what is the default water flow rate that Netro app uses to calculate watering. I did some tests and guess that it might be around 38 mm/h. Is that right? Having a domestic flow different could distort the data used by the algorithm and might recommend to use personalized settings instead of the default settings. Thank you.

Why when I add manully watering time the humidity of the zone don't  change?

Why the next smart program don't reduce time ?

Thank you.

Is there a way to combine the weather underground rain data with the netro forcast as well as the temp? I have found that netro forcast/ temp tend to be very good but the moisture from rain tends to be off quite a bit,  I have a wheather underground station mere blocks away, but the forecast stinks.

Hi!

My Netro app seems to be watering even though it has been raining a lot prevoius day. Zone is set to Smart - Regular.