Ciao.

Just installed Netro Sprite.

I enjoyed to set up the zones with advanced Smart watering, but I'm not confident with what is reported in "estimated frequency and duration". The frequency showed in the setting page seems too long (e.g. every 6 days)... but, if I see what is scheduled in the calendar it seems much closer to my expectation (e.g. every 2 days).   How daoes it work??

Thanks

Maurizio

Got 2 Whisperer sensors recently. They came up not new (see some scratches on them and signs of use). As a part of install had to reset WIFI settings in order to connect to my WIFI. Pressing power shows red led. Issue is - pressing power 6 times (should switch to WIFI setup mode), does not work either. Still RED light.

Does anyone knows how to fix this?

Thanks.

I see that there is some ifttt integration but is it limited to control language and some data logging. What I would like to see is either an .ics subscription calendar or API access to post the next, scheduled water days by zone. It would have to be updated when the app updates and only needs to look out to the next scheduled watering day (start/end time would be helpful too). This would allow me to see when I need to move yard furniture, etc. 

Please add to suggestion/enhancement list.

Thank you. 

Buongiorno a tutti, 

Qualcuno può aiutarmi a capire se la centralina anche se offline e quindi non comandabile a distanza continuerà a irrigare quanto già pianificato automaticamente?? 

Purtroppo non posso andare prima di qualche giorno e ho paura che si secchi tutto... 

grazie mille 

Saluti 

Stefano 

My sprinkler still goes off when it’s raining?

It’s set to rain delay but still goes off. 

I have an issue/conflict  with the watering adjustments for the sensors and the Smart Zone Sheduling

I have seen something weird. 

• I Have set up the Watering Adjustment for sensors the following I describe o be sure about the problem
• Moisture to Skip watering 50%
• Moisture to Add watering 30%
• Duration 5 minutes (only) -- it is a check

• The Smart Zones are st up the following
• Smart Zone - enabled
• Mode - regular

The watering run today only 5 minutes, when the smart  schedule  defined by the system was above that. As you can see, tomorrow watering says different time runs per zone, but it will run a maximum of 5 minutes. This means that the sensor configuration overrides the Smart Zone. And it should not.

As far as I understand the Watering adjustemt is to add EXTRA watering when needed based on the moisture level. Attached picture

Prior to this setup I had the Duration for Watering Adjustment for 15  and 10 minutes, and you can see in the past days runs, that always run for 15 -10 minutes depending the zone/sensor. - Attached picture

In previous weeks, it was working fine and adding extra watering when need it to keep the moisture levels.

Any idea?

I DID THE CHANGES PROPOSED BY NETRO  and it is not working

Take a look the screen shots

Zones 3,4,5 it is below the 30% trigger

I noticed system was going to water this afternoon so I skied the watering on the calendar hours before. 

When the time came the system still watered my yard?

Why?

And I could not find a single way to stop it.

hi i have watering adjustment enabled based on water level on the whisperer. But is there a way to designate time for watering adjustment? Basically it comes on randomly when it senses that more moisture is needed but can be in the middle of the day when we're using the lawn. Regular watering times are already set to only do mornings and evenings...

Thanks,

Arthur

I had to turn off my water valve to my sprinkler system for a week (ending in a few days) and forgot to disable smart watering on my netro.  Netro thinks it did a complete watering last Saturday, and adjusted estimated soil moisture accordingly.  Netro isn't planning another watering for another 9-10 days.  However no watering last Saturday occurred.  

How best should I handle this?  Is there a way to delete past watering, which will lower soil estimated moisture, triggering a sooner watering than currently scheduled?  Or should I just do a manual long watering as soon as I can?

Buonasera a tutti, 

Da questa mattina la centralina non mi chiude più la valvola della linea 1 dell’impianto... ho provato a fare reset ma niente continua con irrigazione!! 

Sono riuscito a sospendere irrigazione reimpostando da capo la centralina ma il problema e sulla linea 1 che non a trova più anche quando metto programma irrigazione.

Grazie mille 

Greetings from Italy

this Monday I will receive my Netro Smart Irrigation controller and I have some concerns about the power supply.

On the YouTube video guide I saw there are 2 slots to put the power cables but I was only able to find a regular 24V power adapter with one single output.

Do I have to cut the power jack off and split the cables in order to put them in the controller?

thanks in advance for your help, can’t wait to become part of the Netro family!

this is the power adapter I ordered: Alimentatore 220 V – 24 V/1000mA https://www.amazon.it/dp/B00AWU8NUM/ref=cm_sw_r_cp_api_i_OBgjFbJ8Q41F1

this is the Netro device I ordered: Netro Sprinkler Smart Controller, WiFi, Meteo consapevoli, Accesso remoto, 12 Zone, w/o Adattatore di Alimentazione https://www.amazon.it/dp/B07DGT7ZK1/ref=cm_sw_r_cp_api_i_iCgjFbP0QZ4DH

is there any way to water twice a day. The time allotted is 60 min max, I need more time my doll is sandy and the temps above 90! 

Right now the watering schedule the Netro program is using for my St. Augustine grass is killing my grass. I live in Dallas and Jully/August is brutal on lawns. If I water outside the schedule the program has established the schedule is changed. Is there anyway for me to water my with Netro and keep the smart watering schedule Netro has? Right now I by pass the Netro by manually engaging my water values, not using Netro. 

Thanks,

Will

Hi, I'm a new user of Netro and for the moment I find it very functional. But it would be very convenient to have the integration for Home Assistant, a very popular open source home automation management platform.

Thanks

Lorenzo

Hi 

I am a new user here and just installed the Netro in my house. The “Smart watering” schedule seems very odd to me.

As you can see there are 2 rounds for each zone and the time of zone 4 is about an hour in one round. Is this normal ?

Bowie

Hola! Acabo de instalar mi Netro al sistema de riego. El el equipo antiguo tenía dos fases, pero ahora la instalación para que funcionara me obligaba a utilizar la celda “M” y me he quedado con una sola fase para todo el riego. Como lo puedo solucionar? 

Hello, I set the app to run 3 manual programs on the odds day and I have the smart watering system active on all zones.

Will it skip my watering if there is rain in the forecast on an odd day?

Dear community

I wondering what is the best moisture level to keep for lawn. The sensor is somewhere around 42%, after watering the garden. Is that enough, should it be more?

Thanks community for your help.

I have two sensors installed for a few days but the humidity still marks 98% why?

No funcionan los aspersores 

Indica Network error cose 2507