I have a whisper installed and was wondering if the setting "Moisture to Skip Watering" is based on topsoil or subsoil moisture.

Is there any plan to allow for Smart things compatibility on the Netro units?

This season when I put my whisperer back out to monitor my garden bed I looked on the app and no longer saw that device. So I went through the process to re-add it to my network and my Netro account and I get an error message stating that that serial number is already registered.  Anyone have any thoughts on how I can de-register and re-register this device?  Thanks

For the last week all the watering events in my calendar show an exclamation warnings symbol. But I have no way of knowing what that means. I have no alerts from the system. My grass looks like it's dying. What is going on? 

How do I reset all the programs in the watering schedule and clean up the calendar ? 

Can a pump delay be programmed between zones?

Thanks

Hi, sorry but is there the possibility of a web interface, without using the Netro app?

Sensor 2 says moisture level is 7% after very heavy rain, but the weekly view says 92% 

If wifi is disrupted will the controller continue to water acording to the most recently programmed schedules?

More generally are there any modes of failure (other than loss of power to the house) where the controller can unexpectedly halt watering?  It would be unacceptable to have one's garden die from lack of water if the system fails when one is away from home for a number of days.

I'm evaluating whether to by a Netro and one of the things I need is to be able to name zones rather than have a zone called say "Zone 6".

I don't see any users manual on your site to answer questions like this.

Hi

I use Netafin pressure compensated drip hose on all my beds and there doesn’t seem To be an irrigation type for that. Is it OK using the drip setting which seems to be for micro drippers. 

Thanks

I do enjoy my Netro, and the app makes things pretty handy.  I do have a couple of questions.

Are there any plans to allow the software to rearrange the zones in a watering cycle (or is that already available and I am just missing it?)  Right now it seems I am stuck watering in the order I have wired the controller.  It would be nice to water one zone, let that soak in while watering another zone, then come back and water a third zone that is adjacent to the first zone.

Another question I have is - is it possible to copy a schedule so that I do not have to set each of the 5 zones for every schedule.  There are times when I would like to run a one time schedule that follows my normal dry schedule,  or follows my moister schedule.

I understand that Netro estimates water usage based on time, emitter type,  and square footage,  but I  have access to actual flow rate via a Flume flow rate monitor. Is there a way to replace the flow rate estimates with actual rates for each system? 

Hello,

I to plan buy Netro Sprite splinkler controller. But I need know if I need pay any fees for using Netro app. Because the app using account at netrohome.com websuite.

Many thanks for early answer

Best Regards
Roman

Hi, 

I have a bed garden with multiple types of vegetables. My irritation type is drop emitter and I bought the humidity sensor Whispered and Pixie.  My garden surface is 100 square feets

I wan to know what is the best app settings to have the best results. The app contains lots of settings and I am little confuse!

thanks

I replaced my Rainmachine with a Netro but I cannot configure it to do what the Rainmachine did. I live in Austin And can only water 1 day a week. Water is incredible expensive so I  cannot use Smarzone because my water bill will be too high. I want to run each zone for 20 min once per week and not water when rain is expected or it is raining. Netro does seem to be able to do this. Any suggestions?

Hello, i have a netro sprite with 6 zone, i need controlate when i watering zone 4 (example) on sprite... open the pixie too. It is possible ?

Thanks you Sebastian

Hi there,

I recently installed the Pixie, and have set up both the smart feature and a regular watering program. The watering program was supposed to go off this evening, but it didn’t. I then checked in the schedule, and all I saw were any restrictions and the smart watering schedule. My program was not there. I set the filters to show me the enables program, but it still does not appear. I have no way of telling with the program has been initialized. Is this a glitch? Should the program appear on the schedule? Why did it not activate when it was supposed to?

Thanks.

Hi

Had to replace a solenoid on the valve on one of my 2 zones and when I do a manual 5min watering on zones 1 or 2 none of them start. I can hear the click of the main valve opening but none  of the zone 1 or 2 valves is opening...if I use the override on the valve to open manually, the water does pass...seem the controller is not sending any open command to eather solenoid of zone 1 or 2 ..

Thanks for your help :)

Hello All, I have three zones and created a program to do a deep water for 20 min. Starting from 5AM and ending at 6AM which is expected to run every 3 days. This morning was the first time I ran it and noticed on my home screen it said watered for 5 min. Any reason why this changed? I'm thinking smart watering has to do with this? If so, I'd like to try and keep this feature for the rain aspect (not to run when it will rain). I read if you disable smart watering (which I can't find this feature anymore), then it will still run the  program when it rains,anyway if I'm in the right ballpark to have your cake and eat it too. 

Thanks in advance