I had a malfunction in one of my valves and one zone watered all night, without metro knowing. That zone is well watered but metro thinks it needs watered. If I turn it off the program it just makes matters worse. How do I get the hydration level back up in one zone without turning off water to my sprinkler system? I still need to water other zones. I need to adjust the hydration level of one zone. Let me know. Thanks

How to delete all zones and start over

How do I add the Whisperer sensor as a sensor with my existing Pixie? It let me add it as a new device but when I go into my Pixie, the option to pick a sensor is blank.

Netro Whisperer sensor throws misleading and confusing data.

I have 6 Watering zones. I have my weekly watering scheduled to run zones 1-5, never 6. For some reason it is skipping over zones 1-4 and only executing zone 5. I just deleted the whole program and started over to see if that fixes the issue. Does anybody know why this might be happening?  All zones work fine if individually run. 

Hi, I’m moving and leaving our Netro system at our old house. I just need to know if it will continue to water when I cancel the internet service for that house?

I just find it alittle ridiculous to pay an internet bill for only the sprinkler system to run.

I am putting down some new sod Thursday.  My last controller had a new lawn setting that ran for 15 minutes four or five times during the day.  Is there a way to set that up with this controller/program? I think I'm running a sprite, netro version 2.5.3

Hi, I've been trying to integrate Netro with Google Home. The Pixie is connected in my Netro app. After logging into through Netro through my Google Home app. The following message appears:

No devices were found in your Netro account.

What is the issue?

Why is not possible two valves operating at the same time if the pump can be operate correctly?

For some reason my controller goes offline every once in a while. It messed things up because it shows all of my zones are underwatered when I’m reality they have been watered. Is there a way to switch it from one with network to a different one that is closer. I can’t seem to find how to update the wireless network for the controller

I really only use Netro to be triggered by IFTTT.  I know it's in Beta but has anyone had success with it?  Mine seems to resort back to syncing evey hour..

Hi,

I have a whisperer that monitors zones 1, 2, and 3.  Zone 1 is the primary zone.  Because whisperer detected a moisture level that was too low it did an additional watering of 10 minutes.  The strange thing about it is that it only watered zone 1 for the additional 10 minutes.  Why didn't it water zone 2 and 3 when they have the exact same conditions and moisture levels.  I had to go in and do a manual run to even out zones 2 and 3 with zone 1.  

Also in the beta software when you try to switch from basic to advance watering or choose a different watering algorithm you get an error message.  

How can I set the Netro up to  water only on two specific days - the same days each week?

I removed an older controller and replicated the wiring when installing the new Netro.  Everything appears to be correct?  However, when watering is activated, the valves will fill up and vibrate or what not with water rushing internally.  But the sprinkler heads don’t pop up and no water comes out.  Any help here would be greatly appreciated.  Thanks!

How do I incorporate a rain sensor (or other device) and make it override expected rainfall?

I am supposed to be in a rainy period but have missed the heavy stuff completely so that my pixie just remains off after reading the forecasts.

What’s the best way of correcting for actual rainfall?

whisperer solar photovoltaic protector film degradation is normal after 6 months?

Jose

We had 1/2” of rain this afternoon and the scheduled watering came on tonight. Is there an easy way to stop watering all zones for that day?

Hello

With smart schedule on, sometimes I see "moisture all day" sign to some zones.

What does it mean and what do the application do? 

Thanks

Shai

Hi 

i received Netro programmer

no connection

i have a fritbox 7560 

the server status message says

mqtt blocked port 1883 

Buenos días hace una semana que instalé Netro 12  estaciones

He perdido la señal wifi en tres ocasiones. He observado que para que vuelva a estar en línea debo desconectar de la corriente eléctrica y volver a conectar el programador,. Me gustaría saber si esta es la manera normal de proceder.

Por otro lado también he observado que si esta fuera de Línea, no riega el jardín lo  que  supone  un problema, pues el programador no lo tengo en mi vivienda habitual.

De que manera puedo resolver estos dos problemas.

Un saludo