What are my sprinklers not going off per schedule? I have a schedule that it supposed to kick off Tuesday and Thursday. It is set to start at 6:00. It is 6:50 and it has not went off. I just had to manually run a cycle. 

Dear Sir

I just bought a Netro Sprite 6 and I cannot connect to my wifi. I am in the middle of the installation and just would not connect. I am using Google network and  Unifi Long Range system (2 wifi networks) and I double checked the password. Tried both of them.  It worked with the humidity sensor but not with the controller. I really tried for 20 times. I will need help for the connection or I need to send it back.

Gabriel

I have successfully installed the device and I start the manual watering on a chosen zone.

The LED changes from green to blue and everything seems ok, except that nothing else happens. No valve is activated and thus no irrigation. 

I have checked with a multimeter and none of the outputs gives the 24 VAC. But the device is correctly connected and seems to work fine. 

What can I do? 

I've checked that My netro isonline...but if i start a manual irrogation app say to me "communicating" and never begin to start..... If i turn off elecrticity and turn on again..... And then i go to manual  Irrogation and press start irrogation begin immediatly

Someone can help me to connect to my unifi Wifi tm sensor Pixie ?

All goes OK unitl last step.... when it tell me that I connect connect to it

thanks

Hi Team,

I would need your help how can I take like an daily backup of my system?

I have Spark-16, Smart Watering Controller.

Or do you have any script for that then could be provide to me?

Regards, Zsolt

Hi, my Netro goes offline every day/couple of days. Probably there is a disconnection of the Internet provider during the night.

Is there any possibility to program an automatic retry of wi-fy connection in the Netro?

Waiting your kind reply

Regards

Carlo 

why if Netro is so smart after months of learning with the whisperer still uses the "humidity to add watering" data set by me and doesn't create a custom program?  smartzone is in advanced level and regular mode.

After a lot of time working fine, suddenly whisperer is crazy. With no reason suddenly the humidity is at "0" and the temperatures are above "90". I have cleaned with water the whispers. I have cleaned the device with water but remains doing same random mistake-

Thanks.

I would like to have alerts about for instance when the whisperer is running out of battery etc...

I have turn off the Netro irrigation on the 1rst of march using the app due to water restriction on my area.

I also use to download data using the API, my surprise is that moisture estimation for each zone are not calculated from first of the march because of the irrigation was stoped.

I think must be independent the stop watering action with the calculation of moisture levels…because the Netro is active and connected to Internet and everything is on, the only action that I took was to turn off watering, not turn off all the system!!

Thanks

Jose

How can I program the app so that it does not do automatic shedule watering, only those programmed manually, I only want the gespa dalt and gespa baix dryers to irrigate 1 minute a day.

Thanks.

This is so damn frustrating to use.

I set to water every odd day.  Start in March.  It’s March 3rd no watering being done and the app says next watering April.  

Any suggestions?   Been struggling with this app for two years now about to give up

Hello!

1. How can I enable notifications (when watering, sensor moisture level…)?

2. Cannot set my Wunderground station ISANTA605.

Thanks!

This thing creates a smart schedule and never follows through.  Give me my money back you thieves.

Please advise how I can change the location. I am staying in Windhoek, Namibia.

I do not understand how many millimeters to set. I have microsprinklers of 4lt/h and 2lt/h. I thought to set to 4000ml/h but the max is 100ml/h.

How to calculate? I have a big terrace with 30 plants and various microsprinklers.

Thank you,

Vieri

Hi there.

Trying to add my fifth and sixth Whisperers to the App, but I keep getting the error:

"Unable to get your location. "Please enable the location service on your phone."

Location services are on and the permission is set for the Netro app.

The app says "getting location" when it starts, but when adding the Whisperer, still says it can't get the localation.

Have rebooted the phone twice. Turned location services off and on. Unset and reset localtion permissions for the app, but still no progress.

Do I need to wipe all the data from the app? Will this lose all my settings or are they backed up in the cloud.

Cheers.

Hi

I am struggling to set up the watering days

There isn’t an option for 4 / 3 / 4 rostered days which is are allocation here in Perth Australia

Please advise

TIA 👍

After 6 months of whispere’s exposed to sun, the protective layer of screen is started yo be deteriorated, losing the transparency property and protection to UV, meaning is catching up less sun.

Answer from Netro support after several exchanges had not been at the right level, despite that last topic was really well addressed.

“Thanks for your info and it should not affect the normal use of the sensor. Please let us know if you see any further issues during use.“

Check pictures and make your statement, but I am not convince about quality of manufacturing of the whispered elements.

David