Dear customer,

A single Pixie device can only be paired with one sensor. Unfortunately, it is not possible to assign two sensors to a single Pixie unit. If you have any further questions or require additional assistance, please feel free to reach out.

Thanks,

Wency

Netro Support

Dear customer,

We noticed that at the moment, weather data visibility is available. However, please note that synchronization of weather data may take a bit of time after the device is online.

If you have any further concerns or questions, please do not hesitate to reach out to us. 
 
Regards, 

Wency
Netro Support 

Dear customer,

Could you please send us email to support@netrohome.com with your Netro account registered email?
We will have our technician look into this issue. 

Thanks
Wency, 
Netro Support

Dear customer,

The Stream's water inlet is designed to be placed in a continuous water supply, such as a bucket or a container, and a pond might work as well. The Stream then pumps water from this source to water your plants. 

However, placing the Stream's inlet directly on a faucet might not have the best results. Secondly, if you’re looking to use the Stream with a specific zone of your Sprinkler system, it's important to note that this Sprinkler zone needs to have a water storage feature. Without it, we cannot guarantee a consistent water supply for the Stream’s inlet, and therefore, they may not be compatible for use together.

Thanks,

Wency

Netro Support

Dear customer,

Could you please let us know your plant type? Different plants need different watering strategies. If your zone grows shrubs or trees which typically have longer roots than grass and absorb water from deeper soil, it takes more days for the moisture level to drop. To refill the mositure level up, it takes longer time running the sprinklers too. 

Thanks,

Wency

Netro Support

Dear customer,

Could you please send us email to support@netrohome.com with your Netro account registered email?
We will have our technician look into this issue. 

Thanks
Wency, 
Netro Support

Dear customer,

New plant mode aims to maintain a high moisture level (above 85%), but it doesn't guarantee daily watering. You can try with the 'new plant' mode and monitor its impact on the growth of your plants.

If you do not want smart zone schedule to override your own programmed schedule, you can set up the Smart Zone level from Advanced to Basic through Settings->Zones->Smart Zone,  which only skip rainning days for your programmed schedule. 

For more information about Netro smart watering, here is an article about Netro three watering modes which might be helpful. https://netrohome.com/forum/posts/111

If you have any further concerns or questions, please do not hesitate to reach out to us. 
 
Regards, 

Wency
Netro Support 

Dear customer,

The picture is not displayed. Could you please send us email to support@netrohome.com with the picture and your Netro account registered email?
We will have our technician look into this issue. 

Thanks
Wency, 
Netro Support

Dear customer,

Yes you can set up programs on the controller using hotspot. Sprite will continue to execute the next 32 pre-loaded schedules if the Wi-Fi connection is lost, for example, the router or the internet service is down.

Thanks,

Wency

Netro Support

Dear customer,

May I inquire if this "5 seconds on, 1 min off" pattern occurs consistently during watering, or is it an occasional issue? Also, could you please let us know when this behavior started? Please press and hold the reset button for 8 seconds to do a hard reset to reset the unit to see if it works.

1.Power off the device(unplug the power adapter)
2.Wait for 2 seconds, replug the power back in
3.Wait for 3 minutes for the device to start up
4.Press and hold the reset button for 8 seconds to do a hard reset
5.Wait for 3 minutes. This should set the light to slow blinking.

Thanks,

Netro Support

Dear customer,

For the backup feature, when the device is online, netro will pull and save normal schedules. When the device is offline, it will continue to execute the normal schedules that was pulled down previously. After the normal schedules are all executed, it will generate a backup program if the backup program is saved.

The backup feature can continue to operate until the internet is restored, executing the stored schedules locally. The backup is designed to prevent interruptions in watering, ensuring the soil remains adequately moist after completing the fixed-duration watering at a specific time each day.

The faulty valve detection relies on monitoring the voltage and current of the water valve's operational state. As for measuring the volume of water consumed, it's a consideration for future developments.

Dear customer,

Could you provide a diagram photo of the water pipes to help us better understand the location of your pump? Could you please send it to support@netrohome.com?

Thanks
Regards, 
Netro Support

Dear customer,

We will have our technician look into this issue and get back to you soon,

Thanks
Regards, 
Netro Support

Dear customer,

Could you please send us email to support@netrohome.com with your Netro account registered email?
We will have our technician look into this issue. 

Thanks
Regards, 
Netro Support

Dear customer,

Could you please send us email to support@netrohome.com with your Netro account registered email?
We will have our technician look into this issue. 

Thanks
Regards, 
Netro Support

Hi Gary,

We have updated it for you from the server side. If you encounter any issues, feel free to contact us.

Thanks,

Wency

Netro Support

Dear customer,

If you want to use and program with the app, You can go to Settings->Account->Language to choose Italian.

Thanks,

Wency
Netro Support

Dear customer,

Would you be able to power on the device and keep it online at your convenience? We'd like to take a closer look at the device's status.

Thanks,

Wency

Netro Support

Dear customer,

Could you confirm if your water valve and your power adapter is 24VAC? Not DC.

When that zone is watering and you cannot stop it with your Netro app, please unplug the power adapter of Netro sprite, see if the zone is still watering.  If unplug the power adapter, the zone is still watering, this zone valve need to be checked. 

Thanks,

Wency

Netro Support