I have a Netto controller 12 

It starts the water pump but not opening any valve 

Hello,

I get this error only on a couple of zones.  See the attached photo. As you can see the zone "misc" shows error.  Any ideas 

I have 2 zone in full sun with hydrangea and Japanese maples. I need to increase the length of watering time on the automatic watering cycle and the frequency

Hi,

My Whisperer 1 doesn’t show any signs of life after two weeks in bright sunlight.

I’m pretty sure the battery or charging circuit is dead after no use for over a year.

Do you offer a repair service or replacement battery?

Regards,

Andy Fiore

Hello,

Zone 4 out of my nine zones will only run when I manually  turn the  controller valve  in the box in the ground, and not from my metro sprite app. I tried removing and inserting the zone 4 wire in the Netro slot , but still no luck . All the other zones will run from the app except zone 4. Please help.

Hello,

After the winter only one of my three sensors shows in the app.  (Twisty Baby Locust).  The other two do not, and when trying to add back in the app errors out as they are already associated with my account....how do I find them and get them back?  I have charges both to ensure good power, and waited multiple day for them to sync, but still missing.

Thanks

Dan

Hi Team,

I've setup my controller to skip 2 days water if more than 10 mm rainfall is reported.

I have local weather station: https://www.pwsweather.com/station/pws/KADAECOWITT

Which is reported 32 mm, smart zones are enabled , but controller won't skip for 2 days.

Could you please ?

Controller SN: 0cb815314670

Regards, Zsolt

Good afternoon,

How could I get The Netro app user’s manual?

I woukd like to understand all the concepts, parámeters and  options in the app

Thais in advance

It seems like, from my communications with the support team, that the soil moisture indicated by Netro does not factor into sprinkling times other than understanding how sprinkling time changes soil moisture (essentially guesses soil type). I have had to very expensive weather stations, and both failed to accurately report rainfall in as little as three months. With religious cleaning of them (ladder climbing-dangerous) neither accurately reported rainfall for more than six months. My first station Accurite 5-1) was replaced at three months and I gave up and bought an Ambient Weather WS2902-C, which lasted less than a year. So….

Why not have the Whisperers determine actual rainfall- or better yet- make your next product the only digital rain gauge on the planet that actually works? Or, perhaps gen 3 of the Whisperer can have a rain gauge built in. When you get multiple Whisperers  per zone, working in the software, the soil moisture readings alone could make reported rainfall irrelevant. 

Thanks,

Kirk

P.S. The support team HAS to stop using the term “soil humidity”. It makes them seem like they don’t know the difference between a fluid (water= moisture) and a gas (vapor=humidity). The Whisperer cannot calculate evaporative likelihood and doesn’t know the air pressure above the soil, so it can only measure moisture, which would, to some extent, measure the influence of water vapor on the moisture, depending on how it was being measured. 

Hi Friends, on The APP I Turn on a sector manually but when I ask APP to Turn Off, dont do!

ONLY Turn off if I unplug The system .

Can you help?

How do I reset the length of time sprinklers are on?

I cannot activate my PIXIE-Z1 to water, it is with brand new batteries, it says 100%, it is online and app and webpage react as all is fine and watering, but unfortunately nothing happens with the device. It works if I push twice the button on the device.

What could the issue be?

Thank you in advance

When I Launch the program , it stop after few minutes…

I don’t know why ?

When pausing a zone for any reason during watering cycle, the zone is skipped. Is there any way to pause it then resume the watering cycle in the zone that was paused?

My whisperer used outdoor gave me an alert here thru the Netro app saying it has 19% battery remaining. What does it mean? Is the solar no longer working? Is there another way to recharge it or can the rechargeable battery be replaced?

Thank you

Hi everyone,

my Netro Spark 8 controller connects correctly to Wi-Fi and shows as online in the app. However, when I try to start irrigation manually from the app, it just stays on “in communication” and nothing happens.

I’ve already tried:

• Using a different Wi-Fi network (even a mobile hotspot)
• Replacing the controller with a new Spark 8
• Restarting both the app and the device

If I activate the valves directly from the controller, they work fine — so it’s not a hardware issue.

Any suggestions on how to solve this?

Thanks in advance!

– Stefano

Any way for end user to open and replace battery on a whisperer 2?  It is out of warranty.  

Hello everyone,

For my lawn i have 2 watering zones, is there a way to "force" schedule to combine those 2 zones to always follow each other? I dont want to water half my lawn on Monday and the other half on Thursday. 

Thank you

Can you have multiple locations or do you have to setup separate accounts?

If separate accounts, how do you do that?