How does the Spark test the valves?

I want to connect a 24V input sensor on the spark outlet channels to switch 2 knx connect valves in different location. Cabling to those valves is to long for 24V. 
The valve testing always says that there is not current and switch it off --> Do i need a resistor on the outlet to simulate a valve? If yes, which value should the resistor have?

Thanks,

Peter

Hello

My system has 5 solenoids.  All worked fine until recently.  One will turn on and off manually.  

However in smart timer it turns in but not off.  

How can I confirm if a app set up issue or a hardware issue with solenoid itself.  

Nath

Hi,

I have a Netro Pixie  and I was wondering if it's safe to leave it outside in the garden during the winter. The temperatures here in North of Italy can drop as low as -5°C (23°F).

Is it okay for the unit to handle these conditions, or would it be better to move it indoors to avoid any potential damage? In any case is not expected to perform any watering activity until Spring time.

Thanks in advance for your advice!

I live in Conroe, TX and I cannot get the manual operation to come on. I’m supposed to water every 2 weeks during the winter months if I have not had rain. No rain in over 2 weeks so I need to turn it on. I do not have anything programmed right now. Any suggestions?

I have a Flume on my master water meter.

Is anyone familiar with any integration between Sprite/Spark and Flume?

Thinking of scenarios like:

If Flume water is already in use heavily (can be defined) then delay watering

Logic between Flume and either Metro to help with faulty valve / leak detection based on water (augmenting Spark's*)

If Flume detects water is shut off, don't run any Netro programs

* I read in Wency's reply at (https://netrohome.com/en/forum/posts/3479/show_question) that 

"The faulty valve detection relies on monitoring the voltage and current of the water valve's operational state. As for measuring the volume of water consumed, it's a consideration for future developments."

.

Hi, I am just about to sell our house and with it the Netro Retic system. How do I change the owner email? I’ve tried it in the app but it keeps failing 🙁 

Thanks,

Andrew

Hi, I am just about to sell our house and with it the Netro Retic system. How do I change the owner email? I’ve tried it in the app but it keeps failing 🙁 

Thanks,

Andrew

System went offline at 2 in the morning and I can’t get any response. Checked the outlet and it’s working. Tried to reset. Unplugged and plugged back in. Help!

Please help. I'll provide a reward for getting my N-12 to work.

lss

I don’t know what’s going on my Netro spark randomly started on its own at night. 5 or 6 times a night for 1 min up to 10 min. Yesterday it ranned for nearly 90 minutes. How can I prevent this?  

One of the sensors started giving humidities form 80 yo 30% from one hour to another. I changed the position of the sensor and restarted various times. Now the sensor measures 0% humidity. 

Now after 4 days the sensor is dead. Tried charging and still doesn't start or show any life.

Any ideas to solve this problem?

Regards. 

Hi,

I've just installed a Spark 16 and I'm playing with the settings. I tried out a zone photo that hasn't really worked but can't seem to find a way to delete it.

Can someone help please?

Hi do you sell the smart solar powered netro wi fi tap timers direct,i need 20 thanks 

Trevor Pfeiffer

The two zones on the Netro Stream Smart Indoor Watering System are in reverse. When I select Zone 1 manually on the machine or from the app, the water squirts out from Zone 2. And by selecting Zone 2, the water comes out from Zone 1. Anyone else having the same issue? Is this something I can fix as a DIY, like opening the box and swapping out the two wires? 

Hi.

My controller operates but many times, rather than executing the time setting. It just cuts out? 

I do have a sensor connected but I took it out of the ground to exclude wet soil feedback 

I'm guessing there is a parameter forcing the stops? 

Could anyone give me a direction where to look? 

Thanks 

This morning my 16 zone Spark unit was showing a red LED.

The app said it was online but when I tried to manually water a zone, it just said "connecting" for the duration with nothing happening outside.

Our wifi was running as normal and the room with the controller in had a good signal.

Unplugging and plugging back in solved the problem but it doesn't leave me with much confidence of the unit if it's going to do this at a critical time of year without being noticed.

Is there a reliability issue with the latest firmware?

Why ? 

My Pixie Z1 has lost connection with hub. Have reset multiple times, just comes up with hub not detecting any deices. Have replaced batteries,

reset, with no luck. Is the unit faulty? Purchased on 6/6/23. Bought a Pixie 1 so have nothing to check Hub.Have reset that several times to.

As previous question, netro showing offline, but green on box. Not watering.

Have reset network and reconnected. Same.

Suggestions?

Hard reset?

Regards

Brett

We are using your API example, where ABCDEFG is the device key.
Using this example, we're getting the following error returned: {"status":"ERROR","meta":{"time":"2025-01-23T10:15:30","tid":"1737627330_uXNP","version":"1.0","token_limit":2000,"token_remaining":1993,"last_active":"2025-01-23T10:15:30","token_reset":"2025-01-24T00:00:00"},"errors":[{"code":4,"message":"Invalid sensor","params":{}}]}, 

It is the same when we use the actual device keys for our Sprite and Whisperers 2.

Could you please help understanding why we're getting the error number 4 "invalid sensor"?