Hello everyone, I have a problem.

To test the system, I started the “manual operation” function. For startup everything is ok but I can’t stop irrigation anymore. I have tried re-configuring the system several time, but I cannot solve the problem. Can anyone help me? 

Thank you

Hello. It would be nice if it were possible to customize the home screen. Select the product that appears by default when entering the app. Is it possible? I have different devices and I used one more than the other and the least used one always appears when I access the app, I understand why it was the first purchase. Thank you very much

Hi,

I installed the sprite control unit.

I attach photos regarding the hardware and software version.

At the end of the installation I performed a manual test of the zones.
The problem I encountered is that at the end of the operating time the watering does not stop.

 How do I solve this problem?

One of my zones is connected to a valve that controls pool fill. What "Plant Type" & Soil should I specify to get smart watering.

Does anyone know what the exclamation icon means on the Metro App under schedule? 

I assume it means it didn't run, but why? These are the water schedules setup by Netro, I don't touch them. See screenshot.

Thanks in Advance!

Tim

How can I add a secondo whisperer to my pixie? 

I just enabled my Metro after winter sleep. Unfortunately it doesn't get forecast information from any of the possible services... I live in Germany. Please help...

Thank you 

My sprinklers decided to schedule a 45 min watering on its own. 

Only noriced it was on when there was onlt one minute left.

Now rhe manual operarion is somehow set at 45min and even if I chanfe it to one minute it goes back to 45. I worry it will go off in the middle of the night at unschedule time. 

Water is precious where i live. We havent had any rain since November. 

How can I stop the app to set schedule on its own for crazy amount of time?

I need to run watering programs 2-3 times in a day, every day. I have "two fra m es" checked but it only will do one.  What do I  need to do?

I have 6 zones but only 4 require to switch on the pump. How can I switch the pump individually on each zone?

Hi. Im a new user and everytning seems to be working ss it should but i get the following message when i check the server status

Hi. The app wont let me add my wundergound id number (IWAGGA24). Can you please help

Hi,

Is it possible to upload data from the app so I can keep record on an externat file for more than a month ?

I would like to keep record for a year long. 

Thanks, 

David. 

Hi Netro,

One frustration I have is that manual run times are important to me but cannot be longer than 1 hour (or programs) and cannot be adjusted while running.

I have Netro connected to a solenoid that controls watering of our small vineyard.

I rarely water in any way other than manual, because I need to control the amount of watering and also use fertigation to feed the vines.

Due to the amount of water required, I need between two to three hours of watering. I also like to adjust as I go, depending on how long the fertigation takes, so the ability to increase time without stopping the watering is also important.

My other solution is to disconnect the wire from Netro and use a Shelly 1 instead, whereby I can turn the watering on and off as I desire.

I would rather just use the Netro app, given that everything is already connected.

It is quite limiting to not allow hours as well as minutes (or to allow more than 60 minutes). amd not to be able to increase (or decrease) the time while the manual run is going.

Hello again, i found that i can set night times on the webpage, and it get sets on the app after that.   But if i try from the app i cannot set any night times.

Hi,

We have a Netro Pixie that we have been using to water trees in our backyard.

We purchased two Whisperer 2 sensors to help understand how much to water.

We paired and installed one sensor which is linked to the Pixie.  This sensor works well and reports light, moisture and temperature and appears in the app in the zone watered by our Pixie.

The other sensor installed as "standalone".  This sensor does not show up on our app including in settings.

How do we access this "standalone" sensor or data?

thank you.

I have purchased 3x Wisper 2s and 3x Pixies as well as a Spark. I want to set the watering frequency based on information from the Whispers. In the app, it has a sensor field, but it's not selected. I can't find any instructions on getting them to work together. I opened a ticket with support 2 days ago but no response. 

Hi guys, 

Is it possible to integrate nestro smart sprinkler to home assistant? 

Thx!

Hi there, Ive noticed that some of the pie-slices in the moisture/temperature/lux graphs from my Whisperer Plant Sensors are heavily coloured (darker) and some are lightly coloured (lighter). Is this supposed to indicate something? 

I suspected that maybe the difference in colour reflects upload as either live (or cached), but I double checked and they all have >50% wifi connection strength and report regularly...

Put Sprite in "paused" mode in winter 

To put Sprite in "paused" mode in winter, you will have winterize your system. First you will have to blow out the sprinkler. You can look at this video to find some useful information. 

https://www.youtube.com/watch?v=s3YRbJYmvgA&t=99s

This video mentioned that you will have to turn on the sprinkler, so you can use the instant manual run feature in the home page to manually start watering for each zone to make sure all the water is out of system.

Then you should put Sprite in "paused" mode just in case some one (for example the kids) accidentally starts a manually run from the app. To put Sprite in "paused" mode, you can go to the Home page->"Enabled".