I'm experiencing a serious issue with my Netro Spark 16 controller. It connects correctly to Wi-Fi and appears online in the app, but when I try to start irrigation manually, the app just stays on "in communication" and nothing happens.

The problemm is with the 4g Vodafone/HoMobile provider as yout mentioned in https://netrohome.com/en/forum/posts/4052

I have already asked several time the update for the device, but nobody reply me

i wrote also to Netro support email: support@netrohome.com  --> nobody reply me.

What should i do to have this update?

Please

I'm curious if there is a way to restrict or cap the calculated volume of water used daily for smart watering schedules. For example, my well produces about 3500 gallons a day or close to 4.5 CCF. I have a storage tank where the water is stored. Is there any logic that can be added to the smart watering calculation or scheduling to account for a daily water volume budget? 

Way Netro had changed my user password?

Hi, I just bought the whisperer 2 and would like to have it as only sensor for the entire garden, however is allowed to have maximum 3 zones for sensor. Is there a way to link all the zones to it? I have 7 zones.

Thanks

How do I change the wifi network my Netro controller is connected too? I cannot proceed beyond step 2 from the instructions on the app. I get the message "Please connect to Wi-fi network "Netro_IRC_xxx."  However, the app shows that I am already connected!!

Good morning, I installed a Sprite 6 controller, it works perfectly, but I have three questions: 1. How do I change the irrigation percentage without changing the watering minutes for all the zones each time? 2. When rain or wind is forecast, does the irrigation program still skip even if the smart function is not enabled? 3. When I start a zone in manual mode, for example to control the sprinklers, is it normal for there to be a long delay between pressing the Stop button and the actual interruption? Thanks.

Someone can help me?I need change the day for one program exists...what is the procedure? Thak you

Can I use the Netro Spark 16 if I use the Rainbird ESP Me? I have 15 active zones.

My system is connected to a 500 liter tank. If I turn on both zones, it empties in 13 minutes.

In the application there is no possibility to program the maximum irrigation time for each individual area. I want you to work at most 13 minutes!

Buongiorno,

ho riscontrato un problema con la centralina Netro Sprite-6.
Il dispositivo risulta online e sembra funzionare regolarmente, tuttavia non attiva nessuna uscita: né la master né le due zone configurate. Ho provato ad attivare manualmente tutte le zone, ma senza successo.

Ho effettuato alcune verifiche:

• la tensione in uscita è sempre di circa 11 V AC su tutte le uscite;

• la centralina è stata utilizzata pochissimo, solo con le zone master e 1–2;

• non sono presenti segni visibili di bruciatura o danni hardware.

Da quanto riscontrato, sembrerebbe un problema software, poiché l’hardware appare in buone condizioni.

Resto in attesa di un vostro gentile riscontro e supporto.

Grazie per l’attenzione.

Cordiali saluti,
Giuseppe Sciurba

I've had a Netro Spark 8 working without any problems since last year, but a few days ago it disconnected from the Wi-Fi and stopped working. I tried the reset button as indicated in the instructions, but there's no way to reconnect it. What else can I do? Thank you very much

Hi, I have a Sprite 12 zones and a Whisperer 2 sensor added to the Netro app. However I cannot find any way to setup the sensor so that it inhibits watering if the measured humidity is higher than some value. The sensor is sending correct reading to the app but now it has been raining for few days and the Sprite keeps watering.

I would like to disable watering based on the sensor only and not on the weather forecast.

If in the app I select the Sprite, then go to settings>zones and select one zone i see the setting Sensor as "Not connected" but there is no way to connect a sensor. If i select the sensor and go to settings>sensor I see all the settings to change name, light color data send interval, but nothing about rain.

Can someone please help me? Thank you!

Hi.

I have a lawn that is irrigated by two solenoid valves, Zone 1 and Zone 2. Each zone controls 3 sprinklers, and there are overlapping areas between the sprinklers from both zones. I would like to configure the system so that when Zone 1 runs, Zone 2 also runs at the same time, and when Zone 1 is off, Zone 2 is also off. In other words, both zones should operate simultaneously to avoid certain areas always receiving extra water. Is there a way to set this up with the controller?

Non riesco a connettere metro spring con metro wisperer

Hi,

Is there any interoperability/integration existing or planned with home automation/smart home platforms?

Integration with Homey Pro would be great, being able to fetch the watering status for each zone, start a manual watering, or send some external triggers (humidity, rain water tank level, etc.) 

Thank you !

Arnaud 

One, and only one ,of my 4 Pixies occasionally sticks in open mode, not closing the valve, watering until I notice it. It won’t shut down from button and I have to turn it off or remove battery to get it to reset. It works for a few days and happens again. It has been working well for about 6 months. Any ideas how to fix this?

Is there a way to remotely reboot a whisperer sensor?

I am on vacation adn one of the sensors is showing up weird values in all the parameters. 

Hi everyone,

I'm experiencing a serious issue with my Netro Sprite 6 controller. It connects correctly to Wi-Fi and appears online in the app, but when I try to start irrigation manually, the app just stays on "in communication" and nothing happens.

Here’s what I’ve already tried:

- Restarting both the app and the device  
- Using a different Wi-Fi network, including a mobile hotspot  

Despite these attempts, the problem persists.

Thenks

Why is Whisperer not showing any moisture reading at all? after working fine for days, it just stops sending moisture info

Hello, I’ve installed netro app on my iPhone, followed the procedure to connect the spark 16 and everything is fine, but when I try to activate valves with the app, the led turn white.

If I remove spark 16 from the app, the led turn green and I can only activate valves from the controller,

Any solution?

Thanks

Davide