Hi,

My Netro-12 is currently running 5 zones at the same time when it was mannually turned on to go each zone at a time, also, the back end of the zones (6-12) does not respond to the app commands and whenever the app said the zones were turned on, it was still the first five zones that were running.

How close does this pixie z1 faucet timer have to be to the hub because it’s approximately 21 ft from it…

WiFi connected

Hub light is solid green

And the timer is offline

Won’t stay connected

Hi 

I just restarted my irrigation system after the winter.  I have tried to manually run a zone.  After watering for 5-10 mins the water turns off but the Netro timer still shows watering.

I am trying to determine whether the pump has turned off because the Netro "on" signal stopped or whether the thermal overload relay on the pump circuit caused it to shut off.  

Is there a way I can check which it may be?

Thanks

Vardhan

I have a broken irrigation and would like to turn off that one station until I fix it.  How do I do that?

Hi there. How can I program specific zones to water twice in one day?

Hi 

I am getting an error in the app like " Invalid group ID 39654: invalid device status "

What would be the reason.  Also I am unbale to pair my device.

Please advise on this.

Thanks 

Ashok.

I have three zones that are running at the same time with low water pressure to all three. This is a new problem. Any ideas on hat might be causing it? 

So far I've tried replacing one solenoid, that did not work. I switched the zones in the control box for one of the three zones but the same result when I activated the switched zone. 

I also tried disconnecting one of the zones, and when I triggered it it did not run. But when I triggered one of the zones I left connected, it did run with low water pressure

Hi gents 

I have setup a new up to 12 zones metro  replacing an 8 zone hunter system.

So far only 5 zones are active

I am missing something small

Hunter old wiring attached 

Thanks! 

First of all, I have been using my Sprite for one year, and the result is very positive. My lawn is better, and I have learnt about how watering should be done in my case. Congratulations to the Netro team. Let me add some questions below.

On 2023-06-13 Wency said "Netro sever side gets/ updates weather information every early morning at around 4 am.

If the weather forecast changes, Netro will update and recalculate the schedule." But could you expand what time zone is this 4 am?.

And a second question is: how often the system recalculates the watering scheduling after a programmed or manual watering? Will that go in the same refreshing as the weather info refreshing? also at 4 am?

Thank you.

Good morning. I am observing that when I manual-water using the web app, and the watering ends, the indicator (blue watering can) remains blue, indicating that the system is still watering. Only resets when the page is left or refreshed. I think that the refreshing should be done automatically, perhaps. The current situation makes the user think there is some hang up in the system, although it is not operationally significant.

Thank you.

I have tried to disable this zone in settings, but it will not disable.  If anyone knows a solutions please let me know.

Thanks

I have been browsing through question from client and have yet to find links to answers to these questions. What is the use of this section of you software if nothing is is fries for answers. Should have a link to follow an answer to all questions. This could prove a lot more useful than just seeing the initial question. 

My sprinkler are set to go off twice they start at 6am then start again around 8am is there away delete the second watering?

We have a 9 zone lawn system and a seperate 4 zone garden system. The controllers are 100 yards apart. We hand 2 Netro controllers and a home network that covers the entire area. Can both controllers be operated with one same app? I’ve tried but without success….must be missing something.

Hi. I have two Whisper 2 units which have started to give strange readings, both have full batteries and strong WIFI connection. One unit is showing low moisture content when the soil is very damp and the other is showing 123 lux constantly. Any help would be most appreciated.

Greetings. Your system is currently compatible with Alexa and Google Home but does not integrate with Smartthings at all. I wanted to know if you were planning its integration. Thank you.

Who can help me? I have three Whispers. 2 working properly. 1 who has worked last year only ‘works’ when connected to USB. Loading works fine. Connecting will work. But when placed in the garden it doesn’t work anymore and loses connection and no lights etc. 

What is wrong? WiFi signal is good outside. He is fully loaded? Is the battery broke? He’s only one year old….. one summer season outside. Whole winter stored inside.

Please help me.

Hello!

We just planted a raised bed vegetable garden with a variety of fruits and vegetables (zucchini, yellow squash, cucumber, green beans, strawberries, 2x blueberry bushes) and I bought the Pixie Z1 to use with a soaker hose setup.  

I just setup the pixie and discovered the smart watering options do not include any of these plants.

Does anyone have successful recommendations for settings that would be best for a vegetable garden?

Thanks!

I connected 3 zones and they were working fine last month. All of the sudden all 3 zones stop to work when I manually run the zones. I tested the voltage using multimeter. It seems the device has no voltage output at all when I run the zone.( I am assuming the correct reading should be about 24V). I tried to unplug/plug to restart the device without any luck. What should I do next?