So happy with how this works. 

Everything works nicely but I noticed a weird issue: I was waiting to fine tune the dripping installation and when the app said Next watering in 1 minute, it was not. Kept saying 2 minutes, then 3, then 5... 

Finally it started some 20 minutes later than scheduled. And the zones were not matching with the real order. In my app it's zone 1, then 2, etc and the app was saying now watering zone 3, next 7, next 2 but surprisingly, the zones were being watered correctly.

Apart from that, it's working great. Thanks.

I have a Spark Controller and the unit is showing me a solid green light but the app is saying offline. I have rebooted my WiFi and the controller with no luck. Any suggestions?

Does it happen to anyone that sometimes the irrigation starts by itself despite the program being set to manual?

I had installed an irrigation controller and one plant sensor and it worked OK. Since I have added one Pixie-1 and one Pixie-Z1, on the app screen when I try to enter innthe red ring bell to see notifications, I am thrown out the app and I can’t see my notifications.

This sounds silly but with most apps offering a dark mode now it'd be nice to get a dark mode option in the netro app. Kinda tired of burning out my eyeballs when I launch the app later in the evening. 

Tyvm

Our watering restrictions are on 6-days a week. Thursday, Friday, and Saturday do not show water schedule. How do I add these days to program?

Hi, I bought 2 Whisperer sensors and when I try to connect to the Netro Wifi, it doesn't show up in my Wifi networks.  The other one showed up no problem.  Is there a factory reset option?

Hi,
I think I am cursed. I had to run a new line for two of my sprinkler valves as I had to move them and it was easier just to run new wire. The sit together in the same hand hole. I am having problems with one of the valves as it goes on when any of the other zones is active. I have replaced the valve once, the selenoid twice (showing solid OHM rating both times. I have the senenoid screwed down nearly all the way. It is the same zone (8) every time. I took a common wire and two others from the new line one went to each valve and the other to the far left common post. The valves, of course, are wired with one from the zone, and the other to the common wire that goes back to the far left C.  When the zone is off it is showing it is throwing about 2 volts AC. I suspect that is normal, or is it a sign of something else? 

I have a Spark 16 and it has been in operation less than a month. 
Thanks,
Kirk

https://identify.plantnet.org/en/namerica/species/Phlomis%20fruticosa%20L./data

I have this plant but cannot find it in the plant library. 

Thanks. 

I have problem connecting netro whisperer gen 2.

I already try with 2.4 wifi but at the end failed.

Any suggestion?

Any issue with iphone 14?

When I click on manual run for my sprinkler system, no blue arrow is there to start on the zone it how do I program them back on so I can do that

Hi, my sprinkler was working till yesterday but today non of the zone is working . Mine shows online and when I run it manually, it shows as running but it is not watering.is that related to Netro server issue ?

Hi,

I've two whisperer and four zones linked to them. I've customized the smart watering setting the correct flow rate of my Sprinklers. I've to set the humidity range for: Tall Fescue, Kentucky Bluegrass,Perennial Ryegrass and three trees: Sweet Cherry, Common Ash, Catalpa.

I want to economize my watering what humidity range I've to set?

Thanks

Hi

Netro light is off everything is connected but it is always off line. I have already changed cr1220 battery inside but light is off not i also have changed the trasnformer no working at all very sad

Hello,

I'm trying to add a whisperer to my system. 

When I go through the procedure, in the app i get asked the address then I press enter and I receive an error message saying that I must switch on the GPS services, which is already on and I cannot go past this. Anyone can help please?

Thanks! 

Dear support,

I’ve just bought and installed the sensor and I’m unsure (and other articles haven’t cleared this) which would be the right setting for the watering adjustment. I’ve set 80% to Skip and 20% to Add. This is for a grass lawn. Is this right?

Thank you

Hi. 

I made a mistake on my netro spark and included a rain delay from the main screen.

How can I delete this delay?

Thank you

Salve, vorrei capire come far accedere il client al programmatore, ho provato ad aggiungere l'indirizzo email, ma sembra che l'applicazione non dia accesso slave all'utente.

Dear all,

We are looking for individuls in the EU (Spain or Italy preferred) who can work with us on shipping, inventory management and marketing. It is a paid, part-time and low-intensity work. 

Please email to carolguo@netrohome.com if you are interested.

Thanks,

Netro Inc

I just developed a Netro Smart Garden integration for Home Assistant.

Take a look here if interested: https://github.com/kcofoni/ha-netro-watering.

Best regards