Hi Guys, 

I have some questions, which answers I couldn't completely find in other posts here.

I have installed a Pixie and a whisperer on my balcony. So far it looks quite good, but it still requires some tuning. 

Unfortunately the house is not well designed which resulted in a complained from my neighbours below me about dirty water dripping onto their balcony, quite soon after I installed the new watering system (with irrigation drippers)

Seems like the Pixie is watering too much, so I went into the settings and configured the SmartWatering with Advanced and tweaked the settings such that it resulted in ~1 min watering per day.

My first question: All over the app, 1 min watering seems to be the minimum - is this correct? Is there a plan to enable even shorter cycles?

When the Pixie is watering for two minutes some of my pots are already filled up and start soaking to the neighbors. 

I think a 30 seconds cycle twice a day should even be sufficient for me. However, I couldn't find a way to get below 1 min. Neither with manual, nor with SmartZone.

So, my current solution would be two have 1 minute in the morning and 1 minute in the evening. That should work on dry days. 

However, I've not quite understood yet, when the SmartZone (if set to basic) skips the watering. It's only depending on the weather forecast, right?

When checking the Whisperer settings, I can also select watering to be skipped and added at certain thresholds. At what times are those waterings added? And at what intervals is this repeated? 

E.g. Add watering set for 50% to 1m. Does this mean it adds 1m watering for that day? once? at what time?

Actually I'd very much like to use the SmartWatering Advanced features, but it just waters too much for my small plants on the balcony. I'm not sure, how I can archive a smart watering behavior in the best way, considering that it should water quite often, but optimally less than 1m, because my neighbors don't want to have a dirty and wet balcony all the time ;-)

And yes, I could reduce the dripping amount at the sprinkers, but this also would mean that it's not spread at all and really just dripping. 

Looking forward for some tips or hints,

Kind regards & stay healthy,

Lukas

Does it automatically stop if it rains? 

Hello,

 Is there a way to use the subsoil reading vs the topsoil reading from the sensor.  For example the top soil reading always reads 100% but the sub soil says 55% which is more believable in Florida's Sandy soil.  The unit did not water for 27 days and still read 99% and sub soil at 20%.  I watered it to see if it would change.  When I take the sensor out of the ground it does change state.  

Hello!

In Netro app, Settings=>Preferences=>Scheduling I have told my Netro Sprite to use the time frame 18.00-21.00 (6 PM- 9 PM).

But when I look in Schedule it says it's going to start watering 06.00 (6 AM). Something is wrong here?

I have a lot of mixed zones and am trying to decide what to categorize them as for smart watering. I have a zone that is an in ground avocado tree, grass, to avocado trees in large wooden containers and also, believe it or not, pumpinks. What setting should I use?

What is the difference between Forecast vs Expectation? Is the 0.2 threshold the total amount of rain for the entire day or per hour?

Hello,

When I set up not to water when wind (daily peak) is higher than a certain set value it seems that Netro will not water during all the day even if in many hours that limit value is not reached.

In my idea Netro should not water only during hours in which wind is higher than the limit value.

Look at my location wind forecast for today - from DARKSKY. During the day there is a great variation in wind speed.

 

for example today wind load of 10 km/h is reached only between 12:00 pm and 17:00 pm..then the system could water in differents hours outside that time range

then if i set wind limit at 10 km/h the Netro app should check if during allowed irrigation time range (or programmed) the  hourly speed limit is reached, not the daily wind speed limit. And in case shift the irrigation time to an hour in which hourly wind speed is lower than the limit.

Could be useful to be able to choose between set daily wind peak or hourly wind speed as limit.

thank you

Which is the difference between specify time range into preferences/programming and restrictions rules?

it seems that programming set a run time range to be applied to all zones while restritcions is a more flexible way to set time range and many other rules that can be applied to all or to specific zone. is it correct?

if programming time range is (completely) different (means never overlapped to) from time range set with restriction rules..what happens? not watering at all?

Can I use the whisperer to control watering of the Sprite controller? If I turn off smart zone. I notice you have Watering adjustment on the whisperer sensor where I can set moisture threshold to add watering and moisture threshold to skip watering. Would this work. I'm using this to water planters and small raised beds. Advice appreciated.

Hi

Following the acquisition of Dark sky by Apple and news that hey will be shutting down the API, will Netro be able to work with dark sky as a weather data provider?

If sprite skips watering as rain is forecasted. But in actual if received less rain, will it increase watering time in schedule for next few days. 

Hi , I'm an Italian happy owner of the netro sprite since last summer :)

Last year I used a classic static programs, this year I want to try the smart side of the platform, I've set my seven zones (square meters,type, etc), but I've some questions:

1) I've two zones with Photinia Fraseri Red Robin (zone3,7), in the database I've set the "Photinia Fraseri", but I've a doubt for the area in sqm, is it square meters or linear meters? If I try to set 50sqm or 25 the water not change, is it correct?

2) The algorithm put 107minutes every 14.5days, I've ask to my gardener and he told me that it's too much water (about double) for that plants in this period. Can i set up only this zone with customs specs?

3) I want to buy the Whisperer sensors, but in Amazon.it there is only the sprite, if I buy by netrohome portal the delivery may be slow, there are additional customs duty,etc. Any chance to see in Amazon.it?

Thanks in advance

This is my set up.

I have a netro device + whisperers 

I have set up the netro to skip the previous day and the next day after raining.

I also have set up the schedule for watering from 6 am to 7 am.

If moisture is above 50%, then watering is skipped.

Yesterday it rained a lot and today all the zones were supposed to be skipped. But one of the zones went down to 45% of moisture and watering was started at 19:22.

1) why this happened?

2) Can I change the moisture level to a lower one? Current limit in the application is 50%

I had consistent rain yesterday and today and foreseen by smart watering but it still announces watering tomorrow!!?? Why? Attach screenshot

Hi,

The sprinkler is not automatically shut off during rain. I have to go to the apps to shut off 

Hello,

first of all, thanks for your product.

I would like to know which Is the best and most reliable weather forecast for the south of Italy (Apulia region).

Waiting for your feedback.

Kind regards

Hello

After connecting, my smart watering controller works well. But when the time of programm os elpased, or i order to stop watering, the current in the wire is still on. I need to open the circuit and disconect zone wire to permit the electrovan to close water flow.

Why smart controller don’t stop the current order to the ev ?

I am in the process of designing my dripping system for my beach house in FL. I am thinking about using 2 Pixies and several Whisperers. I have several questions: 1) What happens when the WIFI is down? Does Pixie turn watering off/on on its own? 2) Does Pixie skip a watering cycle when raining? 3) Are the Whisperers connected to the Pixie and App in that the humidity information guides the amount and frequency of watering? 4) What is the recommended soil humidity for new planted palm trees? Thanks, Markus

I have my first period of rain coming up, so the smart schedule isn't planning on watering until Christmas Eve. Since getting the sensors working properly I've been very happy with the smart watering, but the rain predictions here tend to be a bit sketchy. As my system is saying it won't water because there is rain expected, does it automatically adjust itself and water if the predicted rain doesn't arrive?

Also, I have it set to not water if expected rain is 5mm. What is the difference in this context between expectation and forecast?

I am exploring different smart watering modes. The normal mode waters the lawn too long for me but the eco mode too little. It appears that the eco mode is exactly the same as normal but the watering time is half of normal.

In my case, I would like to set up a smart mode that waters 75% of the normal. How can I configure the smart mode to do that?