Hi

Netro light is off everything is connected but it is always off line. I have already changed cr1220 battery inside but light is off not i also have changed the trasnformer no working at all very sad

Hello,

I'm trying to add a whisperer to my system. 

When I go through the procedure, in the app i get asked the address then I press enter and I receive an error message saying that I must switch on the GPS services, which is already on and I cannot go past this. Anyone can help please?

Thanks! 

Dear support,

I’ve just bought and installed the sensor and I’m unsure (and other articles haven’t cleared this) which would be the right setting for the watering adjustment. I’ve set 80% to Skip and 20% to Add. This is for a grass lawn. Is this right?

Thank you

Hi. 

I made a mistake on my netro spark and included a rain delay from the main screen.

How can I delete this delay?

Thank you

Salve, vorrei capire come far accedere il client al programmatore, ho provato ad aggiungere l'indirizzo email, ma sembra che l'applicazione non dia accesso slave all'utente.

I just developed a Netro Smart Garden integration for Home Assistant.

Take a look here if interested: https://github.com/kcofoni/ha-netro-watering.

Best regards

I have noticed at times when I’m using the app that it states that it is watering when it is not. I checked the schedule, and the schedule does not say it is watering either. Any suggestions as to why this is happening? Thanks.

I just got the new pixie z1 and it doesn’t control the water from the faucet. When I turn it on the water simply flows through as if the smart faucet isn’t there. Also I did not receive my smart sensor for the ground and no responses from the emails I have sent you you. 

Jason Willis

Jason@wishsystems.biz

Hello

Quite often I have my Netro controller disabled and then enable it quickly to be able to do some manual watering.

What would be useful is that, after the manual cycles, the unit would return to disabled mode (i.e. preserve the state of the unit as it was before the manual watering). This would stop the automatic watering from starting unintentionally.

Good morning,

I already have the Sprite 12 and want to add one or two Pixies. 

Do I need the hub for the pixie or the sprite12 acts as hub?

Thank you!

Sergio

I bought a Netro controller, installed it, and everything works. When I try to integrate it with Alexa, it becomes complicated. I already downloaded the skill and associated my user, but it doesn't appear in Alexa. It only works when testing the skill. Does anyone know how to solve this issue? Thank you.

I have purchased Netro Sprite from Amazon. I'm now trying to purchase a couple of Whisperer units. Is there anywhere in the UK as purchasing from the online shop the delivery charge is over $26.

Thanks

Phil

How do I cancel a schedule watering on the Netro App? I set up a schedule for heavy watering but only wanted to run it 2 days, now I can’t figure out how to cancel the schedule! 

I have 10 zones set up in my Netro system.  How can I create a program that will "zero out" specific zones while setting up desired minutes on other zones?  Right now, I had to select the minimum "1 minute" for the unwanted zones since "0 minutes" is not an option. 

I have 2 new Pixie faucet timers.  One seems to be working just fine so far.  The other will not shut off the water.  They are both set to Advanced Smart watering but the one never shuts off the water even when it is not on a scheduled watering and it says it is online.  Do I possibly have something set wrong?  Or is it a faulty device?

Five zones. One not getting smart watering. Ideas on how to correct this? Thanks. 

Hi 

i have continous problems with 

Sprite / app

Never before

Disconnection to wifi

Even when say : online 

it works randomly ( start/ no start  manual 

irrigation )

I swapped out a Hunter ProC controller with a Netro Spark 16 zone controller  The zones all work fine, but the pressure is now too low   When I ran a valve test all of the zones were normal but I had an error message for the Master that says “open circuit”   Not sure what it means or how to resolve it   I checked the wiring connections and they seem fine. Has anyone else run into this ? Thanks 

Neil 

good evening, I have 4 valves connected under relay and 3 direct, the 3 direct valves work correctly but on the first 4 I always get an E2 error. is it possible to disable the open valve control?

Hola,

Cuando estoy configurando las zonas me pide un valor de area, ¿en qué medida? ¿Metros cuadrados?

Gracias