Hi

How I can reset whisper sensor

Like hard reset

I got one reporting 129 c temperature 

Of course it’s hot outside but

Not like that 

I have three whisper sensors,  all of them  but one is reporting moisture levels.  Temperature and sunlight are correct, but moisture is 0%.. I have reset the self learning, Did a hard reboot, and  Reattached the sensor to a different wireless network.  What else can be done?

I added the sensor as a stand alone, then added it to a pixie. Now I can’t figure out how to delete the whisper from the drop down screen. I go into settings and there are no sensors to choose from. Screenshots attached.

I have 8 pixie faucet timers and 4 whisper sensors:

3 for backyard

3 for front yard

1 for drip irrigation in front

1 for drip irrigation in back

I’m trying to assign the 3 front timers in a single zone and sync with 1 whisper sensor. So far, the sensor only seems to sync with 1 timer and each timer shows up as a separate zone.

Also want the same for the back yard. Is this possible?

Can pixie timers be used to create zones?

One of my whisperers gives a zero reading on all metrics about twice every 24hours. Other times it seems normal. Is it broken?

I have a front yard with zoysia grass, about a thousand square feet, no trees. My app keeps telling me that it will water this grass tomorrow. It is obvious that it needs watering, but the next morning I see that it has not been watered and it says I will water it tomorrow. There is no rain forecast, it has been very hot. It Waters the rest of my yard properly, it's just my front yard that it does it like this. Why does it keep changing its mind?

Also this same area, my front yard, has no trees but the app says there are trees on it. And I cannot change it. I would think if this area had trees on it it would be taking much more water and the app would water more. How can I change this on the app?

Is there any way to increase the font size on the rain and irrigation charts in the app.  Alternatively can the data be switched to a table with larger type?   Or zoom?

I am having difficulty setting up my timer.  I have Netro connections, but I can not seem to make my phone connect to schedule a time for irrigation.  manual does not have good information on trouble shooting this issue...

I need help with that.

I signed up to be a beta tester but have never received any information or a beta version of the app to test out. Anyone actually beta testing anything?  Maybe I just wasn’t chosen to participate.   

Can I use my app to set up another device that will be on a different WiFi? It is for my Mother’s lawn and I would like to get it set up using my phone

Bonjour,

comment puis-je tester mon installation, avec le robinet ouvert pour voir si tout fonctionne ?

merci

Good afternoon

I would like to know if I can use one of the channels that I am not using for irrigation, to be able to use it as a timer to turn the lights on and off in my garden

Thank you

Greetings

What is the ideal soil moisture for the following:

• Tomatoes;
• Soft herbs (parsley, cilantro, dill); and
• Hardy herbs (rosemary, sage, etc)?

Is it not possible to correct today rain to a value lower than 1mm?, the app said it has rain today 2mm but I want to correct it to zero mm.

thanks

 I purchased a second Whisperer. I added it via the Netro app, and it shows up on the app start page.  As it is in a different part of the USA than the first sensor, I wanted to assign  a different location but the app does not seem to allow this.  Am I missing something?

Is there a way to activate a watering manually without having to restart the pixie or wait until it syncs? I just want to press manually water on the app and have it start. I’ve tried it with the ‘stay online’ beta feature and it still says ‘watering in xx minutes’.

Hi 

Got my Sprite in March, but my whole irrigation installation got finished two weeks ago and then installed the Sprite for the first time. It was troublesome to say the least, android was not helping when switching between the Netro wifi and router, but somehow got it working. A couple of days later it was offline, but managed to reconnect. Today I checked again and it was offline, did everything the the troubleshooting page recommnend and nothing worked, even placed a wifi repeater just to be sure. Ended up resetting it and even that didn't work, the connection process always ends with a network failure message.

Edit a couple of hours later: been trying to connect again, the behavior of the app is like two weeks ago at the beginning. When trying to switch back after connecting to the sprite wifi, the login screen appears and off course the whole process is interrupted

Edit 11.07.2021: Made an attempt to reconnect again, worked but inmediatly after the Sprite was offline again...

This is of course very frustrating, please help getting the Sprite working properly.

Mi temporizador recibe más de una hora de sol al día y tiene puesta la sincronización cada 4 horas sin embargo debo cargar la batería cada semana con electricidad ya que se queda a 0 % cada 6 a 7 días  

Hello, I have just bought and installed a new Netro in my garden. I am running the smart watering option and have 2 questions:

Madrid has a weather quite warm and dry, reaching more than 105 F, but these days we have 85 F (minimum at night 65 F)

1-. How to reduce te watering times but still use smart watering option (Netro is seting almost double time that I had with my manual program, my lawn was green enough). Those watering times would be aceptable for hot days, I suppose.

2-. The 4th zone is used for plant pots. Netro is setting 2 followed watering periods everyday of  3 or 4 minutes each . Thats is too much and the water flows out from the container below the pot. Wouldnt be better to water 2 times but separately during the day?

Thanks!

Nacho

Installed - but now only 4 of 9 zones work, thoughts?