When trouble shooting it would be nice to have a test run button so you could just run all the stations one minute. You can manually run each station but you have to do it for each station which is a pain. I have someone working on my system and I have to run it for them and stand there to run each station.

Hello I’m having an issue when I try to manually turn on a zone it doesn’t go on. It always worked and started doing this. I trying restarting the whole thing and when I turned the zone on by the Solonid the zone comes on fine. Any idea? 

I have had my Sprite installed for a couple of weeks and all seemed well, but looking at my garden I realized it was not watering. When I turn it on manually I can hear a short buzz and water entering the valve, but there is no flow. I can open the valve manually and water then flows. I have reverted the valve to the old timer and it then opens the valve, so I don't think the problem lies there. 

I have the black wire on the valve connected to the common terminal, which was how it was set up on the old timer. I cannot figure out what the the problem is. 

I am an international user with a non-Netro PSU, but it seems to as specified: 24VAC 850mA Adapter AC-AC 100V-240V to 24VAC Power Supply Adapter UK PLUG

Can anyone help me overcome this problem with what otherwise seems to be an excellent system?

Just installed the system yesterday and I noticed zone 5 (of 5) for some reason is getting special treatment over the rest. All zones are set identically for the same types of grass, soil and sprinkler heads. However looking at the schedule zone 5 seems to be getting more attention than the rest (i.e.: only zone being watered during off days)  what's going on here? 

I live in Arizona and it's not really hot yet but it's starting to get warmer and I noticed my rye grass is starting to die off and everybody else's is very green.  I think it's because netro isn't watering as often as it should be when it gets warmer. I'm aware I can set a manual schedule but that kind of defeats the purpose of why I bought Netro. So what I'm saying is I think an algorithm needs to be adjusted so hot dry climates get a little more watering for winter grass that's still in season before the Bermuda comes in.

My whisperer sensor stopped working after a few weeks. Any ideas?

Today, I went around the house to start the season, checking springklers, and one zone wouldn't stop in manual mode. I tried to be closer to home to get better Wifi signal. It still would not stop even if I turn on/off other zone. Shouldn't  manual stop override any previous malfunctions? I had to shut the main sprinkler valve for now because there was no way to stop the water for one particular zone.

Any fix for this? I am planning on a leave and that was the whole reason I got Netro, but this worries me if water won't shut off while I am away.

Why does zone 1 only allow 1 minute manual water sequence and all the other zones it’s 5 minutes. I can’t figure out how to change this? 

Prodotto perfettamente funzionante ma non riesco ad aggiungere l'app a Google Home. Quando cerco Netro sulla lista delle applicazioni compatibili non la trovo. 

Qualcuno è riuscito a configurarla? 

Grazie 

Massimo 

Hi,   

I have received today the netro controller, 12 zones.

I have installed it correctly, 1 common wire and 7 zones.

It has connected to thr wifi easily, no problem. 

I can start any zone from the seven manually, but if I turn off manually, it does not turn it off...

If i start another zone then sometimes it stops the previus zone finally then start the new one..

and sometimes it just does not react anymore.. does not matter what i turn off or turn on manually, it does nothing.... 

but the device receives every command, because everytime when i turn a zone off or on, the led will blink 1-2 but nothing happens.

I checked wire, unwire and rewire again just for sure and tried the another common wire socket... then made factory reset and reconfigured it..

same issue...

it turns off zones compketely only if i unplug it from the socket, then i replug it, then it works until i start 1-2 zones and then again the same issues...

so what to do with it? 

Anyone know why my Sprinklers are still on even though it shows they’re not running in the app? 

On the graph, is the rainfall actual rainfall that has occurred or is that rainfall that is predicted based on weather map?

Hello, 

I am trying to connect my Hunter PVG 101 GB valves to my new Metro Sprite. 

I haven't installed a watering System before so I am quite a newbie here. 

I have managed to set my Sprite up. But my valves aren't working. 

I have double checked my wires. No issue there. As I am living in Germany I have bought my own power supply. It's this one: INNOVATE LED Trafo ECO 24 Volt/DC, 0-50W - LED Treiber - Transformator - Netzteil - Driver (24V - 50W) https://www.amazon.de/dp/B01AALEYR8/ref=cm_sw_r_cp_apa_i_LgCYCb2PT86Y9

Are there any recommendations, what I could do wrong?

Thanks so much,

Is there a way to assign one sensor to multiple zones?

Come posso aggiungere skill netro in italiano grazie 

I have a company doing service on my sprinkler system, and would like to have them able to turn zones on/off to verify coverage and do repairs. Does anyone know how can that be done without me giving them my phone?

Many good questions here in the community but unable to see the answers - why?

Salve a tutti come faccio a collegare lo sprite  alla Amazon Alexa chi può dirmi come faccio grazie

Hello!  I just got a whisper and wanted to add it to a stand-alone zone but keep getting the following error: Error no info about this zip code in our DB. Any thoughts?  I can add it to one of my other zones?  

Thanks.