I have six sensors but use only 3 which are 1, 3 and 4; however, I am having problems with sensors 4.

My sensor shows the moisture way above where I have my watering adjustment set to not water, but it is still watering. What am I doing wrong?

Hi everyone!

My Whisperer Smart Plant Sensor has broken. I would like to know if it is possible to fix it by buying a replacement part or if there is a DIY solution to reuse the device.

Thank you.

Hi,

why after irrigation the humidity is lower than before?

This problem only with 2nd gen sensor...

Thanks

Desde hace unos días la APP no está funcionando. Según la APP el WiFi está OFFLINE, pero según la página web está ONLINE. Según ambos está WATERING pero la realidad es que no está regando y no responde a órdenes. No dispongo en este momento de acceso físico al dispositivo. ¿Podrían indicarme si el problema es un problema local o de la APP/Web?

Hello,
I have two irrigation lines on the same garden, is there any setting that would allow these two areas to be “tied together” such that they irrigate on the same day (session)? (Obviously first one line and then the other).
Thanks

Como puedo solicitar mi estación meteorológica en wunderground a mi cuenta netro?

No me deja escribir el id de la estación ni seleccionarla.

Gracias

How do i activate a replacement Pixie and connect to existing (old) name and schedule in the app?

Hi 

I have bougth a Netro sprinkler w/o adaptor for an offer on Amazon IT.

Unfotunately i though a 24Dc adaptor would be OK but valves don't turn off while using program and manual irrigation too.

Point is that it is very hard to find an Ac Adapter 24V in our country.

Could you please help to find some place where to retrieve one?

Thanks

Buongiorno, ho alcune domande:

1)è possibile far partire solo una zona specifica attraverso i comandi vocali su google assistant?

2)è possibile aggiungere un altro meteo diverso da quelli proposti?

3)perchè quando applico il ritardo pioggia la pianificazione intelligente impazzisce e pianifica male?

grazie in anticipo delle risposte

For some time the system worked perfect. Now I  have two sections that don't work. It turns out that the signal to activate the valve is too short. When I  put a meter on it and then activate the valve the meter jumps to 28v for about one second then drops to zero before the valve can move. Conversely the one that works stays at 28v for much longer. I have rebooted and reset the system.  Any ideas?

He instalado el programador y de vez en cuando salta una de las zonas 

Hi! 

How can I share the Nero application of my watering control system with my gardener?

Thanks

Smart watering has taken over my system. It waters on the wrong days at the wrong times. I have tried and tried to reprogram it with no success. I have asked for support from Netro at least 10 times and they have no support. Can someone please help me and tell me how to program the stupid smart system? It waters my plants three days in a row and then doesn’t water it for four days. My grass is dying. My plants are dying. Everything is dying because Netro has zero support. They don’t even have helpful videos on YouTube someone please help.

My terminal 1 is not working anymore. How can I troubleshoot?

deleting plant sensor??

Hello

I have 2 pixe devices and 2 hubs. I have 1 hub and pixie working fine. When I added the 2nd hub it does not show up in the app and therefore cannot add the 2nd pixie what am I doing wrong

I am doing yard work to 2 of my 3 zones right now and have the whole system disabled for several days as many heads are disconnected.  Woke up a 5am to have zone 3 on and spraying water everywhere for 20 minutes. 

How is this possible? Why do you not update your softwar? 

Hi,

I see a boost factor option in the web interface. I understand it's meant to increase or decrease the watering time. You can see the effect in the estimated watering times and schedules.

In the app, however, that option does not exist and, in fact, it shows a different estimate than the web interface. Why is that? Which one does the system pay attention to? The settings in the web, or those in the app?

Thanks!

Good afternoon

I have plant sensors in all zones, and they block.

Sometimes i have my grass really dry and the sensor have 70/80 % of humidity.

I turn them off change place like 2 cm, turn them in again and they have the correct humidity.

Anyone experience this?

Thank you in advance