hi i have watering adjustment enabled based on water level on the whisperer. But is there a way to designate time for watering adjustment? Basically it comes on randomly when it senses that more moisture is needed but can be in the middle of the day when we're using the lawn. Regular watering times are already set to only do mornings and evenings...

Thanks,

Arthur

I have an issue/conflict  with the watering adjustments for the sensors and the Smart Zone Sheduling

I have seen something weird. 

• I Have set up the Watering Adjustment for sensors the following I describe o be sure about the problem
• Moisture to Skip watering 50%
• Moisture to Add watering 30%
• Duration 5 minutes (only) -- it is a check

• The Smart Zones are st up the following
• Smart Zone - enabled
• Mode - regular

The watering run today only 5 minutes, when the smart  schedule  defined by the system was above that. As you can see, tomorrow watering says different time runs per zone, but it will run a maximum of 5 minutes. This means that the sensor configuration overrides the Smart Zone. And it should not.

As far as I understand the Watering adjustemt is to add EXTRA watering when needed based on the moisture level. Attached picture

Prior to this setup I had the Duration for Watering Adjustment for 15  and 10 minutes, and you can see in the past days runs, that always run for 15 -10 minutes depending the zone/sensor. - Attached picture

In previous weeks, it was working fine and adding extra watering when need it to keep the moisture levels.

Any idea?

I DID THE CHANGES PROPOSED BY NETRO  and it is not working

Take a look the screen shots

Zones 3,4,5 it is below the 30% trigger

I noticed system was going to water this afternoon so I skied the watering on the calendar hours before. 

When the time came the system still watered my yard?

Why?

And I could not find a single way to stop it.

My sprinkler still goes off when it’s raining?

It’s set to rain delay but still goes off. 

Buongiorno a tutti, 

Qualcuno può aiutarmi a capire se la centralina anche se offline e quindi non comandabile a distanza continuerà a irrigare quanto già pianificato automaticamente?? 

Purtroppo non posso andare prima di qualche giorno e ho paura che si secchi tutto... 

grazie mille 

Saluti 

Stefano 

I see that there is some ifttt integration but is it limited to control language and some data logging. What I would like to see is either an .ics subscription calendar or API access to post the next, scheduled water days by zone. It would have to be updated when the app updates and only needs to look out to the next scheduled watering day (start/end time would be helpful too). This would allow me to see when I need to move yard furniture, etc. 

Please add to suggestion/enhancement list.

Thank you. 

Got 2 Whisperer sensors recently. They came up not new (see some scratches on them and signs of use). As a part of install had to reset WIFI settings in order to connect to my WIFI. Pressing power shows red led. Issue is - pressing power 6 times (should switch to WIFI setup mode), does not work either. Still RED light.

Does anyone knows how to fix this?

Thanks.

It would be great if you add an option for notifications once irrigation starts/finishes.Sometimes we need to start it manually and need to wait until one zone is completed to start the next one. A notification in the phone would avoid opening the application all the time to see if the current zone is completed. 

Ciao.

Just installed Netro Sprite.

I enjoyed to set up the zones with advanced Smart watering, but I'm not confident with what is reported in "estimated frequency and duration". The frequency showed in the setting page seems too long (e.g. every 6 days)... but, if I see what is scheduled in the calendar it seems much closer to my expectation (e.g. every 2 days).   How daoes it work??

Thanks

Maurizio

Has anyone had an issue with their Sprite being inoperable shortly after the warranty ended?  I tested the power prongs with a voltmeter and the controller is getting electricity, but no lights are on.   It's 105 deg in Austin and no rain in sight.  I'm going out of town for 5 days, so I'm in trouble.  I'm going to have to go to Home Depot to get something off the shelf installed today before my trip.

Anyone with the same problem?  Has anyone been successful with a claim outside of the warranty period?

Update:  The Sprite went offline at the same time the LED light stopped working.  The watering schedule resumed two days later and the LED was still off.  Meaning - Sprite works fine, LED doesn't work.  Netro told me to send the unit in over the winter and they will repair the LED.  Awesome - thanks Netro!

All the best,

-Doug

I added a whisperer to one of our zones. Recently the moisture content was between 25-30%. We are having a hot summer with many days with 110 degrees. I believed it and watered for good 15-20 minutes. It turned out despite all those water the soil moisture went up to 45-50%. I went and checked again, the soil looks pretty good and appeared moist. 

Hello.

I installed my netro yesterday and now after watering all zones it shows me that the next watering will be in 5 days. It seems to be to far away in the future since it's 35 degrees celsius and sunny all day

My system is not watering using smart schedule. keeps changing the watering days. even though not enough rain. unable to change the weather station on the app.

I have 2 whisperers. Both have the nightlight enabled to auto but only one of them turns it on at night the other never does. Any advice?

can i get user manual in spanish for netro sprite?

Is water backflow integrated into the Pixie timer or does installation require a separate one?

whem my Netro is disconnected from wifi , all stsyem is out of service !!  THIS IS A BIG BUG !  

Is possible set a automatic program when the connection is down ?

And we are off and running.   Whisper went in the ground and started reporting right away.  Would be nice to connect it to my Ambient weather station as well.   

This is needed in the app. The scheduling is harder then it needs to be.

Whisperer is showing all data and is controllable on iPad, but not on Android?