I would LOVE to have a way to move a days scheduled run (and all subsequent runs) ahead XX days.  For example, if I have all my zones scheduled to run tomorrow, but it is raining today (and I'm scheduled for every third day runs), it would be great to move tomorrow's run ahead 2 days (as maybe it's not raining TOO hard, but enough to warrant not watering tomorrow), and then that move trigger all subsequent runs to move ahead by that many days as well.  Any plans for such a feature?

Hello.
Is it possible to move a Zone, in my case: "Prato e back giardino" from Terminal 2 to Terminal 3 in a efficient way?
Let's say, for instance:  Copy Zone "Prato e back giardino" or Move "Prato e back giardino" from Terminal2 to Terminal 3, without being obliged to cancel the previous and reprogram all in a new Zone?

I've a problem with Terminal 2: the wire broke inside and I am not able to remove it ....

Thanx a lot
Gian Piero

Sensor was removed thru winter. Now will not activate and shows single red light only. Been in direct sun for 3 days so fully charged. Cannot get white light to reprogram.

My rain delay is set to 15 days. How do I reset or delete the current delay?

The program is now scheduled 15 days out, and I have disabled and re-enabled my program in hopes it would reset it. I checked restrictions and the delay is not listed.

Thanks!

Trying to add ISANREMO24 to PWS but I always get this error:

Please enter a valid ID !

Can you fix the problem or add for me:

ISANREMO24

Weeper hoses need to run for hours, the only option in smart scheduling is drip irrigation which is having it max out at like 30 mins a day 

Just go to last page, standard UX

I need to go outside to toggle this thing on off manually which defeats the purpose of having it.

Hello,

I can only add a maximum of 3 zones to my Whisperer Sensor. I wanted to add all my 6 zones to it? Is that possible? 

Thanks

Hello,

I’m trying to setup schedule for watering for next five months, But watering schedule shows only for two next months. I check the settings and I do have a selected five next month. is there something I’m not doing right?

Change the minutes on smart schedule

On my schedule screen sometimes I have an “!” mark. Sometimes it’s a “i” If I tap on the zone it takes me to preferences. Did I make a change that I am not aware of? What does this mean?  Thanks. 

I just installed the pixie timer and i would like to test it. 

However even if i scheduled two test runs, none of them appears in the schedule yet.  Is the schedule updated only once a day? 

Manual run is not available (the timer appears strike-out) so i cannot even test that way.

Thanks in advance for your help

Best 

 Jacopo

I'm not sure what Netro did to the App over the winter but it does not function worth a damn. We turn on one zone manually and shut it off and try and turn on another zone and the first zone state is also on. 

One of our customers has a problem where all zones come on a one time.

Bring back the last version!!!

Good morning,

Randomly my device loses connection and keeps blinking.  I have to turn it off and on for it to get the network back.  The Sprite is five meters from the router and next to other devices that have a good connection at all times.

Thanks 

iPhone -

- Get app

- Crete account

- Go to connect timer

- Next

- Enter name and stuff, next

- Turn on unit, next

- Connect to Netro_* wifi, next

"Please connect to wifi network "Netro_*"......

I have disabled the IP security on the iPhone side. 

Please advise.

In the past week watered alternatively once a day and twice a day for all zones.

In Discover the irrigation cbm are stuck at 0.01 and worse show 0 for the last few days.

Hello, I have 3 pixies installed,  two of them are separated 10cm from each other, so they are in same place, but one of them is most of the time offline... what can I do??

Today has rain a lot and the pixie has been watering for more than 1.5h... that's a lot of water waste. 

Please give me a hand how to solve this. 

Thanks 

Luis

Hello,

I am using one Netro Pixie Hose timer to water 2 freestanding planters via a hose splitter.  I am looking for a way to add 2 Whisperers to the Netro App to monitor both planters for watering needs.  The app appears to only allow one per zone.  Is it possible to add a second Whisperer to the same zone?  I am not concerned about overwatering as the planters allow for extra water to drain out easily.   I just want to make sure neither planter dries out.

Thanks