When I start watering to give it a try. Everything's going well. But when I want to stop watering it's impossible. I have to turn off the power so that netro stops the watering.

WeatherPro is the problem ?

For information, I have an electrovanne rainbird.

 Best regards

Arnaud

Any suggestions? Thanks. Already unplugged from outlet for about 10 seconds and plugged back in. 

hi there, my sprite was working fine for 3 month , now i had no internet for 24 hours and sprite did not connect to the internet anymore . I restarted the router and then the sprite and still no internet connection but my router is fine and i have internet. So i reset the sprite and now it says i need to allow location service on my phone but it is on!!! it will not allow me to setup the sprite and i don't know what to do?

I have two whisperers, one in zone 2 at the front and one in zone 4 at the back. We're in Mexico so it's ridiculously hot and sunny all the time. The unit at the back faces north west. The unit at the front faces north. Both units are now dead. Neither will reset or power up. 

What is the best way to store the whisperer for the winter.  Should in keep it exposed to sunlight via a window.  Is there a way to turn it off?

After exposure >4 hours, the power button lights up red and shows no sign of connection. And one more detail is a Sprite capable of connecting with the Whisperer?

Pls answer me soon because I am in need of to use. 

Thanks

Having a problem since upgrade of the app. Doesn't seem possible unless the main unit updated as well. Valves close within a few minutes of being activated by manual start, or programmed schedule. Have not test with smart watering disabled, but it happens on manual starts, so not sure that is even a variable. The Zone still shows as actively watering in the application. If you submit a stop  action by pressing the red square,then restart, via the sideways triangle, the zone will come back on again. However, it shortly shuts back off, while still showing the zone as being actively watered. This is happening across all four of my zones. Curiously, if you unplug the controller after the valve shuts off, but the app still shows it watering, wait a bit, and then plugit back int-the zone comes backon shortly after reboot.

Tested countless times, hasn't finished a cycle in a month. The zone stops sending the 24v signal causing the pump relay to snap shut and turn off the water supply, or perhaps the zone valve. Either way, appears to be a very odd defect. Do I need a replacement unit?  (BTW, I have all smart fumctioms disabled) 

I have my controller in my garage here in the desert.  The transformer seems very hot to the touch.  Is this a problem??

What does the yellow triangle with the ! mean next to the schedule 

When I started running a scheduled daily program in conjunction with smart watering selected, for some reason zones will run at the same time.

Am I doing something wrong?  I have a one minute delay in my zones and when I didn’t have the program running the zones would run independently.

When I open the app while the two zones are running, it only displays one zone running.  I’m super confused.

Hello, I've noticed that 2 out of my 6 zones suffer from low to no water pressure. I tried removing the nozzles to test but the water kept barely coming out. I know the solinoids are working because the water is coming from the zones, but how can I understand why there is super low pressure?

Recently I have been having issues with zones 5-8 stop watering before the cycle is over, but keeps counting down and moves to the next zone and does the same thing. I have tried resetting the unit, re-linking the wifi, but doesn't seem to make a difference. Help!

Hi there,

My controller has been losing connection to the internet everyday for about two weeks. The controller light stays solid and my app says the controller is offline. I can only reset the controller by physically disconnecting the power supply for 10 seconds and rebooting. This is getting anyoying and is  becoming a daily routine. I have a wifi extender 2 ft from the controller location as well. If I can't depend on the controller to stay online, what's the point of having an internet based sprinkler system? What steps can I take to make the controller stay connected to the internet?

I installed as directed and only have three zones, but every time the system comes on all zones are watering simultaneously.  I installed the common wire as it was removed from the last controller and each valve wire is hooked to zones 1-3.  Any thoughts or ideals are appreciated.  Thank you

I installed as directed and only have three zones, but every time the system comes on all zones are watering simultaneously.  I installed the common wire as it was removed from the last controller and each valve wire is hooked to zones 1-3.  Any thoughts or ideals are appreciated.  Thank you

My new whisperer is connected inserted into the ground as per the instructions.  It has been there for two days through various watering cycles but the app says the topsoil moisture level is 0% ( the subsoil is 88%).  Is the unit defective or am I missing something?

I just received my new Whisperer and when I push the power button, I get one single red LED flash and that's it.  It won't do anything else.  I put it in the sun for a couple of hours to see if the battery was dead, this didn't solve the issue.

hey guys, my smart Sprinkler isn´t working correct. after installing the hole stuff and first testing, i was so happy that everything worked fine. but my hunter valves PGV100 never Closes anymore. for testing i ve connected the valves directly with my trafo 24VDC 1A and it worked fine. so i guess that the zonecontacts working not correctly. any ideas? is the DC Adapter really the reason? i need help, or i send the Netro back to amazon… Hey Leute, mein kluger Sprinkler funktioniert nicht richtig. Nachdem ich das ganze Zeug installiert und getestet hatte, war ich so glücklich, dass alles gut funktioniert hat. aber meine Jägerventile PGV100 schließen nie mehr. zum testen habe ich die ventile direkt mit meinem trafo 24VDC 1A verbunden und es hat einwandfrei funktioniert. Ich denke also, dass die Zonenkontakte nicht richtig funktionieren. irgendwelche Ideen? Das falsche Netzteil? Ich brauche Hilfe, oder ich schicke den Netro zurück zu Amazon ...

My controller keeps losing connection to the wifi. Is there a way the app can send a notification when that occurs? 

Also, my smart watering program skipped the zones during this time. I thought if the controller was offline the programs would continue as  scheduledt? it would be nice to know why the program was skipped, like a diagnosis log of the errors.

Additionally, the controller randomly started the irrigation programs outside my set time peramerters. I'm afraid the controller is glitching out. I believe this all occured when the controller was disconnected from the internet. 

We got our Netro two weeks ago and set up went just fine.

Yard was being watered, great.

Two days ago our power went out, came back on an hour later.

Netro light blinking slowly tried to reconect and all i get is

Internet may not be available, rest of the house is conected.

Any help would be appreciated.

Thank you

Bruce