When I turn on manually by pressing two times it’s fine. However the water turns off automatically after a minute or two. Is this right?  How do I get it to stay on longer so I can shut it off manually 

Also should the LED stay on all the time?

Hi, 

Could we get a notes section in the zone setup so we can record extra information about the zone.  it could be wire colouring for install, notes about other setup / sprinkler install information or general notes about how that zone is performing and changes we might want to make.  

Thanks

Can I have your help with Metrosideros (Myrtaceae) please ? I can't find It in the plants Mame in the Netro App. Sun? Water? Can you suggest me a similar one in the Netro App?

Thanks a lot,

Ale

I am new to gardening and traditionally, I can kill a plastic plant.  I have started a small flower bed with 3 rose plants in it.  

Is there a way to read the information in the app to learn how many gallons have been given to the plants in a given period of time?

My simplistic understanding of the rose plants is they should get 3 gallons a week total.  My current moisture % in the app shows 68.  Do i need to focus on getting that and keeping it at 100%?

Thanks ahead of time for any education you offer.

Todd in Texas

valvole hunter 24vac, netro non apre le valvole.

i collegamenti sono stati eseguiti come da istruzioni.

Quale può essere il problema?

Alimentatore 24v 1000ma e’ corretto?

I have a whisper installed and was wondering if the setting "Moisture to Skip Watering" is based on topsoil or subsoil moisture.

Is there any plan to allow for Smart things compatibility on the Netro units?

This season when I put my whisperer back out to monitor my garden bed I looked on the app and no longer saw that device. So I went through the process to re-add it to my network and my Netro account and I get an error message stating that that serial number is already registered.  Anyone have any thoughts on how I can de-register and re-register this device?  Thanks

For the last week all the watering events in my calendar show an exclamation warnings symbol. But I have no way of knowing what that means. I have no alerts from the system. My grass looks like it's dying. What is going on? 

How do I reset all the programs in the watering schedule and clean up the calendar ? 

Can a pump delay be programmed between zones?

Thanks

Hi, sorry but is there the possibility of a web interface, without using the Netro app?

Sensor 2 says moisture level is 7% after very heavy rain, but the weekly view says 92% 

If wifi is disrupted will the controller continue to water acording to the most recently programmed schedules?

More generally are there any modes of failure (other than loss of power to the house) where the controller can unexpectedly halt watering?  It would be unacceptable to have one's garden die from lack of water if the system fails when one is away from home for a number of days.

I'm evaluating whether to by a Netro and one of the things I need is to be able to name zones rather than have a zone called say "Zone 6".

I don't see any users manual on your site to answer questions like this.

Hi

I use Netafin pressure compensated drip hose on all my beds and there doesn’t seem To be an irrigation type for that. Is it OK using the drip setting which seems to be for micro drippers. 

Thanks

I do enjoy my Netro, and the app makes things pretty handy.  I do have a couple of questions.

Are there any plans to allow the software to rearrange the zones in a watering cycle (or is that already available and I am just missing it?)  Right now it seems I am stuck watering in the order I have wired the controller.  It would be nice to water one zone, let that soak in while watering another zone, then come back and water a third zone that is adjacent to the first zone.

Another question I have is - is it possible to copy a schedule so that I do not have to set each of the 5 zones for every schedule.  There are times when I would like to run a one time schedule that follows my normal dry schedule,  or follows my moister schedule.

I understand that Netro estimates water usage based on time, emitter type,  and square footage,  but I  have access to actual flow rate via a Flume flow rate monitor. Is there a way to replace the flow rate estimates with actual rates for each system? 

Hello,

I to plan buy Netro Sprite splinkler controller. But I need know if I need pay any fees for using Netro app. Because the app using account at netrohome.com websuite.

Many thanks for early answer

Best Regards
Roman

Hi, 

I have a bed garden with multiple types of vegetables. My irritation type is drop emitter and I bought the humidity sensor Whispered and Pixie.  My garden surface is 100 square feets

I wan to know what is the best app settings to have the best results. The app contains lots of settings and I am little confuse!

thanks