I set up my metro system this morning.  I made an error in programming the watering schedule.  How do I reprogram the Smart watering program?  I have been unable to do it.

Also I would like to point out that yesterday at midnight the irrigation started by itself, without having programmed anything, with the app I could not turn off I had to stattare everything through the electrical panel.
As ever this happens, should be a convenience this control unit controlled by the app instead of problems.

Hello, yesterday I mounted the control unit with an electrician, the connections are fine, we tried several times the manual function but it did not work, I am trying in various ways to operate the control unit, after several hours I pressed reset and I managed to start the manual program, now it works but I noticed that it does not start if there is a daily program, is it correct??

Instead the programming does not work on the calendar, I tried in various ways but the irrigation does not start, I think the control unit is faulty, I tried several times to program a minute per sector but nothing works. Now it’s raining here of course I disabled the smart zone so for now only the manual function works, not with programming. What advice can you give me?

Thanks

Rosario

What should my unit light show if it is properly connected?   And where can I find an online owners manual for this product?

Vincent Devlahovich

My netro is using smart schedule. Even though i have ECO on each zone, zones are watering for more than 20 minutes. it rained last night and today morning it was watering for more than 20 minutes.

 How do i change this?

lot of water being wasted. 

Thanks,

Ananth Bandla

Hi!

Tonight at 2.30 my netro start to watering. I had to stop it starting a manual program and stop it because in the app there was no watering sign.

Then I put a restriction for 3 days and around noon netro starts to watering again. There was a lost wifi signal for a minute cause by a voltage drop. 

Is it normal?

Thank you 

It Rains and Netro still watering my plants unless I add daily skips when I see the weather forecast. 

It shows watering, but it is not?

I have an ! inside a yellow triangle showing up on days my sprinklers run. 

What does the ! mean?

My flower gardens have several inches of wood chip mulch covering the soil.  After a season of "Smart Watering" my beds are dry and the perennial plants are stressed.

Does mulch absorb irrigation water intended for the plants?  Is the presence of mulch a factor affecting the duration of an irrigation cycle?

To the Netro community:

We are excited to introduce our new products, the Netro Zigbee Hub and the new smart timer Pixie-Z1. They combined deliver a different experience of smart watering system. 

The Netro Zigbee Hub hosts a long-range local Zigbee network that links all the end devices. It connects to your router (wireless or wired) to transfer data between the end devices and the Netro cloud service. The Hub will work with all our Zigbee products including the new timer Pixie-Z1(introduced below) and the new soil moisture sensor coming this year, as well as the new 4-Zone sprinkler controller and the new weather sensor coming next year.

The new host timer Pixie-Z1 is re-designed from the original Pixie timer in many ways:

1. Always online for instant quick runs. No more sleep mode

2. Powered by two AA alkaline batteries with approximately one year of battery life. Notifications on low battery

3. Supports Google Home and Google Assistant

The Netro Zigbee Hub and Pixie-Z1 are expected to ship in September. To join the Tester program please email to info@netrohome.com and we will send you a discount code in return for feedbacks.

Thanks, 

Netro Inc

I have seen quick stop watering on landing page in app once. Than not anymore. Is this a recent feature? Looks not stable. Meanwhile I cannot see stop button on manual run page where it was before. Shame that everone got wet on garden party.

Hi, I had a Sprite working OK but I needed to move it to another location and WIFI network. I assumed starting from scratch was the easiest method and deleted the controller on the App but now I cant get it back into host mode (<1sec press of reset button) or factory reset it (6-8 sec)....The LED flashes about once every 6 secs or so not every second, no matter what I do. 

So I never see the Netro_IRC wifi network ....

How do I fix this ?

-A

Trying to add a new manager. Any email address I enter results in a "can't find user ..." error message.

Because it rained for two days, I put temporary restrictions on programming my Netro. Now I cannot reprogram it no matter what I do! Any clue what I should do besides the manual or adding new program?

I was told the custom schedule would not let my moisture level go below the min I set but it goes below the min all the time

Hi today the smart schedule wateres while sensors above the 50% humid. I stopped manually. It is weird because the schedule shows to skip the zone but it watered anyway. Zone 3 and zone 4. Zone 1 is correct

May you check it?

Can you guys add weather station

KVACHEST132

We had enabled Smart Watering. It was watering each zone twice, for a very long time - totalling up to 2 hours nearly daily, unless it was raining. I know the standard comment from Netro CS is that it's better to water deeply and less frequently, but this was watering every day...2 hours a day. It's too much. I disabled smart watering, and created my own program, but it 1) doesn't show up in the calendar/schedule and 2) the home page says "Next run not scheduled". How do I enable my custom program to run? Is there some small enable/disable button somewhere I need to use? Do I need to clear everything and start from scratch? We'd love a nice green lawn, but can't water for 2 hours every day (on just a small front yard!). 

Also, it'd be nice if there was a way to talk to a technician. Thank you.

Anyone running into an issue of having two zones run at the same time when doing a manual run?