My Whisperer seems constantly reading 91% moisture when I know for a fact it is NOT ?  Any ideas or how can I report this it is like 2 weeks old ?

My Netro goes offline in the middle of the night every so often, no power outages or Internet outages, so wondering what people are doing wen this occurs short of unplugging and re-plugging it in.  I am thinking of installing a smart plug to reboot it each morning so I don't miss any watering cycles.  What are people doing?

Hi all,

My problem is that in the app it appears that it is watering each area and the reality is that it either does not water at all or water less time. I have been on vacation for a few days and I have found the dry grass and two trees without leaves. A disaster. I have been communicating with the support service by email for several days and I do not have a clear answer to this problem. Can anybody help me?

Thanks a lot,

Daniel

In the daily pie chart the temperature seems correct, but in the weekly chart the temperature is different. The same for other parameters.

The graphic is very poor.

 Any suggestion.

Thanks Paolo

One zone suddenly stopped working. I can activate the zone by manually turning the solenoid. I have unplugged and restarted Netro. In the app, it shows the zone running but no water is flowing. Any ideas?

whisperer solar photovoltaic protector film degradation is normal after 6 months?

Jose

I really only use Netro to be triggered by IFTTT.  I know it's in Beta but has anyone had success with it?  Mine seems to resort back to syncing evey hour..

Hi 

Got my Sprite in March, but my whole irrigation installation got finished two weeks ago and then installed the Sprite for the first time. It was troublesome to say the least, android was not helping when switching between the Netro wifi and router, but somehow got it working. A couple of days later it was offline, but managed to reconnect. Today I checked again and it was offline, did everything the the troubleshooting page recommnend and nothing worked, even placed a wifi repeater just to be sure. Ended up resetting it and even that didn't work, the connection process always ends with a network failure message.

Edit a couple of hours later: been trying to connect again, the behavior of the app is like two weeks ago at the beginning. When trying to switch back after connecting to the sprite wifi, the login screen appears and off course the whole process is interrupted

Edit 11.07.2021: Made an attempt to reconnect again, worked but inmediatly after the Sprite was offline again...

This is of course very frustrating, please help getting the Sprite working properly.

One of my whisperers gives a zero reading on all metrics about twice every 24hours. Other times it seems normal. Is it broken?

I have 8 pixie faucet timers and 4 whisper sensors:

3 for backyard

3 for front yard

1 for drip irrigation in front

1 for drip irrigation in back

I’m trying to assign the 3 front timers in a single zone and sync with 1 whisper sensor. So far, the sensor only seems to sync with 1 timer and each timer shows up as a separate zone.

Also want the same for the back yard. Is this possible?

Can pixie timers be used to create zones?

Hi

How I can reset whisper sensor

Like hard reset

I got one reporting 129 c temperature 

Of course it’s hot outside but

Not like that 

I have one Whisperer up and running just fine. Based on this I purchased a second. The second produced readings that were inconsistent when the device was placed next to the first Whisperer (read about half on moisture when compared to the first). So, I sent it back to Amazon for a replacement. The replacement arrived and it also appears problematic. The light reading is normal, but the temperature is 486 degrees F and the moisture is 1 percent. The device is stuck at these aberrant readings and they are obviously problematic. I've tried deleting the device and reinstalling several times. The result is the same.

Any advice or assistance would be appreciated.

Hi, 

I have pixie for one year, the first year is was working perfectly. Nevertheless when i reinstall it this spring, I observed a frequent problem : 

when pixie start watering, there is like a air cavitation noise in the pixie and the pressure of the springer is almost zero, I have to manually turn off the tap then reopen it ( while pixie is still on) to recover the full pressure in the watering system. Meaning that the system is useless if i am not at home to each time turn off then on the tap. 

Can you provide me some tips to troubleshoot, and fix this issue?

Thanks

Hi!

I am having reconnecting to my home wifi after I changed the router.

I've followed the steps, reset thru the box and can see netro network come up. But it doesn't connect. Tried several times with unplugging the box completely but not resolved.

Appreciate your help.

Hi all, one of my whisperer is not working after the winter season. If I press the button it just blind a red light and then nothing. I have left it under plenty sun for the last 3 weeks but nothing appened... Any suggestion? Thanks

Does the Netro Pixie timer work with low pressure or gravity watering systems? 

My whisperer shows 99% humidity stuck in one zone in the hourly and dashboard views. The weekly daily monthly views all show progressively dropping humidity. Which one is correct and how do I possibly reset this ? Also do my watering schedules get affected by the hourly or the daily humidity ?  My other whisperer shows consistent data between hourly and other views. 

Hi. 

Just renabled netro after winter.  I see that the app thinks it has rained over the last few days, but there hasn't been any rain.i have darksky as the provider.  Is darksky still working?

Thanks

Vardhan

Purchased in Nov of 2020 and stored until recently in basement.  When I went to put it for the season the battery was dead.  I understand it needs to be charged which I did for two days.  When I turn it on, I get solid white, then green and then red.  I also noticed it’s missing from my sensor list in the app. Like it has been deleted.   If I click edit button. Nothing happens.  Can you please help?  Thank you.