What's a preferred setting for watering adjustment on the whisperer for just a grass lawn? (I currently have 20% add water 80% stop water) is that too low/high?

Hi, I have a Hozelock Micro Irrigation system with multiple Universal Drippers that supply 40 Litre per hour. I would welcome any advice on the best way to set up the app, for a Netro Pixie and this setup. Should Smart Zone be used on basic or auto with user fixed schedules.  Any advice welcomed from experienced Nitro users on the best way to use my new Netro device. Thanks.

Hey, I'm a techie and I have a question about your "smart watering". What is the feedback loop that you use?

My zones are vastly different -- some have very small spray heads, and some have very large rotors that pump out a lot of water. At first glance, I cannot see any way to (a) indicate how much water is delivered per zone or (b) indicate how moist the soil actually is.

Assuming that I have not missed anything, I have a few suggestions:

1. Provide a mechanism for indicating the water deliver rate for each zone
2. Provide a mechanism for manually imputing the actual, measured moisture of the soil
3. Provide a "hint" mechanism for each gone (e.g. "This zone is too dry" / "this zone is too wet") which would in tyrn influence the smart watering.

I need the Netro system to water every day in this hot, dry climate. Our lawn is turning brown. It’s used to being watered every day. The smart watering system is watering every 4 days. I have both the frequency set to high and the moisture levels set to high. I do not have sensors. What else can I adjust to get it to run every day. I’m trying to figure out how to choose everyday using the smart system. Do I just need to set manual program? That kind of defeats the purpose of having smart watering (adjusting for rain, etc.)

Thank you for any help!!

My Netro app on my phone and iPad will not let me sign in today. Instead, it shows an error message saying the Netro website certificate has expired and it’s dangerous to login. This is concerning because I did not know that if the website is down, I do not have any control over watering my lawn. None. Is there a way to get around this or do I need to return my sprite 6 smart water controller?

Hi,

If you are using the “basic” smart watering mode, is Whisperer data considered to turn off a watering schedule similar to what is done with the weather forecast?

Thanks,

Andy

Does smart zone adjust water time depending on temperature change?

For instance, does smart zone automatically adjust to water more for those days over 90 degrees and water less for cooler days?

Frequent mode vs regular, which consumes more water?

How do I disable the smart watering programming?  

I have a whisperer in one of my zones connected perfectly. I have a large back yard, so 3 of my zones are essentially the same. No difference zone-to-zone on the sunlight, slope, grass type, soil type, etc...

Can I have multiple zones use that one whisperer for data? I like the soil moisture readings from the sensor (currently sensor zone shows 33% moisture but the other two zones without the whisperer show 65% moisture).

Thank you!

I notice that the IFTTT apps are pre canned. I have 3 whisperers and would like to control 3 different zones. I got around this by choosing a to water when moisture fell below 40% and 50% for 2 different zones. I there a way to trigger 3 different zones at the same 40% moisture?

Again Thanks for your efforts.

Last summer I used Smart Zone Regular mode.  It did a great job but it watered somewhat more than I would have liked.  I checked all the other mode settings and outside of ECO which looked to cut it in half I didn't see any mode that would do what I am looking for.  For customized I didn't see a clear way to have it water say 20% less than Regular mode.  Is there a straightforward ways to do this?   Seems like a nice feature would be to be able to adjust a mode up or down in say 5% increments or so.  That way we would have all Smart Zone Advanced benefits without having to do a lot of manual customization.   thanks

I have a whisper installed and was wondering if the setting "Moisture to Skip Watering" is based on topsoil or subsoil moisture.

Hi Guys, 

I have some questions, which answers I couldn't completely find in other posts here.

I have installed a Pixie and a whisperer on my balcony. So far it looks quite good, but it still requires some tuning. 

Unfortunately the house is not well designed which resulted in a complained from my neighbours below me about dirty water dripping onto their balcony, quite soon after I installed the new watering system (with irrigation drippers)

Seems like the Pixie is watering too much, so I went into the settings and configured the SmartWatering with Advanced and tweaked the settings such that it resulted in ~1 min watering per day.

My first question: All over the app, 1 min watering seems to be the minimum - is this correct? Is there a plan to enable even shorter cycles?

When the Pixie is watering for two minutes some of my pots are already filled up and start soaking to the neighbors. 

I think a 30 seconds cycle twice a day should even be sufficient for me. However, I couldn't find a way to get below 1 min. Neither with manual, nor with SmartZone.

So, my current solution would be two have 1 minute in the morning and 1 minute in the evening. That should work on dry days. 

However, I've not quite understood yet, when the SmartZone (if set to basic) skips the watering. It's only depending on the weather forecast, right?

When checking the Whisperer settings, I can also select watering to be skipped and added at certain thresholds. At what times are those waterings added? And at what intervals is this repeated? 

E.g. Add watering set for 50% to 1m. Does this mean it adds 1m watering for that day? once? at what time?

Actually I'd very much like to use the SmartWatering Advanced features, but it just waters too much for my small plants on the balcony. I'm not sure, how I can archive a smart watering behavior in the best way, considering that it should water quite often, but optimally less than 1m, because my neighbors don't want to have a dirty and wet balcony all the time ;-)

And yes, I could reduce the dripping amount at the sprinkers, but this also would mean that it's not spread at all and really just dripping. 

Looking forward for some tips or hints,

Kind regards & stay healthy,

Lukas

Does it automatically stop if it rains? 

Hello,

 Is there a way to use the subsoil reading vs the topsoil reading from the sensor.  For example the top soil reading always reads 100% but the sub soil says 55% which is more believable in Florida's Sandy soil.  The unit did not water for 27 days and still read 99% and sub soil at 20%.  I watered it to see if it would change.  When I take the sensor out of the ground it does change state.  

Hello!

In Netro app, Settings=>Preferences=>Scheduling I have told my Netro Sprite to use the time frame 18.00-21.00 (6 PM- 9 PM).

But when I look in Schedule it says it's going to start watering 06.00 (6 AM). Something is wrong here?

I have a lot of mixed zones and am trying to decide what to categorize them as for smart watering. I have a zone that is an in ground avocado tree, grass, to avocado trees in large wooden containers and also, believe it or not, pumpinks. What setting should I use?

What is the difference between Forecast vs Expectation? Is the 0.2 threshold the total amount of rain for the entire day or per hour?