更多篩選條件

Cannot find master solenoid valve

kvschlegel
更新時間 2024-07-06 22:46:35 UTC 
None of the zones are watering when the app says it's watering. I measured each zone when active and each read 28 AC. When testing the resistance, the readings were jumping all over the place for each reading. This is leading me to believe there is an issue with the master solenoid valve. However, there is no wire that connects to the M slot on the controller. Looking around the house for any of the underground boxes, I have not been able to find the master solenoid. Attaching pictures of what I have found. Any help greatly appreciated.
瀏覽: 1087   回覆: 2

Manual watering beta

Lynn johnson
更新時間 2024-07-10 04:17:16 UTC 
話題: Netro App
So I like the idea of being able to manually water when I want especially on really hot days but the battery aftervthe second day dies and never charges more then 10 to 15 percent even in full sun for 10 hours. Would be nice if it charged faster and had a better battery or less drain in that mode.
瀏覽: 948   回覆: 1

Problem with irrigation time

Daniel Encinas
更新時間 2024-07-12 10:43:36 UTC 
Hello, I have owned a Netro Sprite programmer for several years.

The problem I have is that it programs the phases intelligently and if it indicates that it has to water for 10 minutes. It only waters for about 1 minute but the app shows that it has watered for 10 minutes. The garden is drying out and I don't know what to do.
This happens to me in all irrigation phases. If I program it manually the same thing happens to me. If I try it twice, the second time it takes even less time to water.
I have connected the transformer directly to the phase, bypassing the programmer, and it works correctly.
Reviewing its problems section, I found a similar one in which it says to look at the 24 volt voltage. (which is correct, around 30 volt) and the resistance in ohms of more than 20 (around 30 ohmios). It also says that there the programmer has a recoverable fuse.

What can I do?


Thanks

瀏覽: 953   回覆: 1

Sprite wont connect to your internet so I can move forward

cjulian
更新時間 2024-10-05 18:05:09 UTC 

My controller has been out almost a month. I have factory reset, short reset uninstalled app, and unplugged it. No matter what I do, i cannot get past the connect to netro wifi step. I need to blow out my sprinklers and I cannot get my device to work to manually run them. It will say its connected and do the spinning wait thing, then suddenly tell me to connect to the netro internet again. When I go to do it again it says no internet connection. Please help me. I sent an email from my email as the registered user (husband) is deployed in the middle east. Please look for an email from "kimbo__@" 


Thanks!

瀏覽: 389   回覆: 1

Netro Whisperer humidity error

Pierluigi Cilli
更新時間 2024-09-08 07:29:59 UTC 

Hi,


why after irrigation the humidity is lower than before?

This problem only with 2nd gen sensor...


Thanks

瀏覽: 677   回覆: 1

Broken whisperer sensor

Jesús López
更新時間 2024-09-09 16:19:33 UTC 


Hi everyone!

My Whisperer Smart Plant Sensor has broken. I would like to know if it is possible to fix it by buying a replacement part or if there is a DIY solution to reuse the device.



Thank you.

瀏覽: 697   回覆: 1

Smart watering not working

Carolyn Seyfried
更新時間 2024-09-10 16:17:51 UTC 
My sensor shows the moisture way above where I have my watering adjustment set to not water, but it is still watering. What am I doing wrong?
瀏覽: 662   回覆: 1

Sensor

Kathleen Hamilton
更新時間 2024-09-11 19:43:50 UTC 
話題: Netro App
I have six sensors but use only 3 which are 1, 3 and 4; however, I am having problems with sensors 4.
瀏覽: 697   回覆: 1

Whisperer says: Sensor XXXX already in your account

Thomas Murphy
更新時間 2024-09-18 12:39:46 UTC 
Hello there!

I'm really hoping you can help me. I bought two Whisperer 2s.


I configured the first one (called Roses 1) and it works perfectly.

I configured the second one (called Office Pot Plant) and it went through the configuration fine but then doesn't appear in my app in the Sensors section (Roses 1 appears, but Office Pot Plant doesn't). 

I tried to configure it again and it told me that the name Office Pot Plant was already taken, but it doesnt show anywhere.

I tried a factory reset on the Whisperer which worked but when I tried to configure it, it gave me the error "ERROR: Sensor XXXX already in your account".  

I've looked at my account on the web and it only shows Roses 1.
So I can't add the device because it says it's there already, and I can't delete it because it doesn't appear!

Please can anyone you help? I wrote to Support yesterday (from the email for this account) but I'm hoping someone has a DIY fix for this?

Thank you so much!
瀏覽: 560   回覆: 1

Zone 1 not watering

11807GFT
更新時間 2024-09-24 23:25:59 UTC 
I have 6 zones and all but zone 1 run.  I start running manually and app says watering but nothing.  I checked the wires, none loose.  It will run randomly but I’m getting really frustrated.  
瀏覽: 563   回覆: 1

Schedules

jonathansalina
更新時間 2024-09-28 11:11:52 UTC 
話題: Netro App
Am I able to create a schedule for new seed that allows me to add 2 watering times (1 in the AM and 1 in the PM)? Right now I had the create 2 separate schedules. 
瀏覽: 506   回覆: 1

How do I?

Rockhead413
更新時間 2024-10-01 00:08:51 UTC 

Help! How do I set up my controller to a connect to my new router?


Vincent Devlahovich 

805-813-1216

Loyal customer

瀏覽: 429   回覆: 1

1 zone not watering

cowlo@xtra.co.nz
更新時間 2024-10-01 01:41:13 UTC 

I have a Sprite which has 5 working zones which are all connected to smart watering, 4 to sections of the lawn and 1 for the garden.  The lawn zones all water automatically but the garden zone only waters manually.  All zones have been set to water automatically via smart watering.

What could be the possible cause of this please.

瀏覽: 460   回覆: 1

Manual mode without delay

Phil Houghton
更新時間 2024-10-04 23:27:59 UTC 
How do I get a manual run without having a delay. Manual should be manual in my opinion. No added delays from his knows where. Please can anyone help?
瀏覽: 383   回覆: 1

Konrad

berlin
更新時間 2024-11-10 09:36:28 UTC 

Hello,

I had to change my google password and now I lost all my datas from my last installation in my Netro system.

What can I do to find it again. Must I install everything new?

Who can help me?


Thank's

Konrad

瀏覽: 188   回覆: 1

Zine will not run

TJ Woods
更新時間 2024-10-27 14:40:45 UTC 
I changed the sprinkler head on zone 5 after installing the new controller. All zones work but 5. I can run it manually. It won’t work on smart watering.
瀏覽: 349   回覆: 1

Zone won't shut off.

shoo.shoo
更新時間 2024-11-10 05:55:43 UTC 

Hi,


I have 4 zones and a master valve. When I run any of the zones, they won't shut off when the timer runs out. If I switch the AC power off, then the valve will shut. I have checked the valve and it has no issue with opening and closing except when the sprite is running it. I tested cables for continuity, and I have tried swapping cables with no change. My ac power pack is AC 24v.


This issue affects each of the valves but only when controlled via the sprite. The valves are fully operational otherwise.


Hoping for a fix, otherwise will return to Amazon under warranty and get another brand.

瀏覽: 165   回覆: 1

Conrtoler

John Zuzula
更新時間 2024-10-19 23:45:24 UTC 
Why is connection lost with my cover on. But when I take it off it then reconnects? My lawn once again looks like crap because this thing glitches out.
瀏覽: 320   回覆: 1

Netro Spark valve testing

Peter Strohmayer
更新時間 2024-11-14 13:49:20 UTC 
How does the Spark test the valves?


I want to connect a 24V input sensor on the spark outlet channels to switch 2 knx connect valves in different location. Cabling to those valves is to long for 24V. 
The valve testing always says that there is not current and switch it off --> Do i need a resistor on the outlet to simulate a valve? If yes, which value should the resistor have?


Thanks,

Peter

瀏覽: 117   回覆: 0

Solenoid does not switch off

Nath Moyes
更新時間 2024-11-15 00:49:20 UTC 

Hello


My system has 5 solenoids.  All worked fine until recently.  One will turn on and off manually.  


However in smart timer it turns in but not off.  


How can I confirm if a app set up issue or a hardware issue with solenoid itself.  


Nath

瀏覽: 103   回覆: 0