I have a Sprite installed at a healing garden--part of a new transitional home here in Sebastopol, CA  for homeless veterans on which I was the project manager.  However the non-profit team who will bring in the vets has not taken occupancy yet and the wifi will be theirs.  It says in the netro installation that in case of no wifi , it "might work to use the "test run" program on your iphone on the log-in page.  But I cannot see the "Test Run" option  on my iPhone 6S.  

Please help because with the corona virus shut down, Netro is closed and  it could be weeks before I can get to the site to water it manually and all the plants could perish for lack or water!!!

Thanks for any help,  Yohan Morgan.  707/332-3050, USA  cell. 

hi,

I put whisperer in a garden pot, after a few days I noticed that it indicated that the soil was moist even if it was not.
it was particularly dry.
two days ago I moved it, I made the calibration and zeroed the self-learning but still today it shows me that the soil is moist while the soil in the pot is now particularly dry, it is necessary to irrigate!
indicates that it is 98% wet.

what is wrong?

and while because from the app I only see humidity of the top soil while from the web with the webui I also see the humidity of the subsoil?

tnks

best regards

stefano

So my whisperer began to fail aboit a few weeks ago. I try reconnecting it and all it does when i press the button is flash a red light. Any help? Cant reset it or do anything at this nm point. 

Hi 

Sprite has been successfully installed and tested once each zone (12).

The next day, the decide was offline without any reason and all the attempts to switch off and reset were failed. How I can solve the issue?

Thanks for the support

Br

BG

The system was working fine when I 1st got it but now when it comes on no water comes out it works for about 5 minutes 'then stops . For when I water all zones the 1st stone will water and then it will cycle through and not water any of the other zones Please help

When I start watering to give it a try. Everything's going well. But when I want to stop watering it's impossible. I have to turn off the power so that netro stops the watering.

WeatherPro is the problem ?

For information, I have an electrovanne rainbird.

 Best regards

Arnaud

Any suggestions? Thanks. Already unplugged from outlet for about 10 seconds and plugged back in. 

hi there, my sprite was working fine for 3 month , now i had no internet for 24 hours and sprite did not connect to the internet anymore . I restarted the router and then the sprite and still no internet connection but my router is fine and i have internet. So i reset the sprite and now it says i need to allow location service on my phone but it is on!!! it will not allow me to setup the sprite and i don't know what to do?

I have two whisperers, one in zone 2 at the front and one in zone 4 at the back. We're in Mexico so it's ridiculously hot and sunny all the time. The unit at the back faces north west. The unit at the front faces north. Both units are now dead. Neither will reset or power up. 

What is the best way to store the whisperer for the winter.  Should in keep it exposed to sunlight via a window.  Is there a way to turn it off?

After exposure >4 hours, the power button lights up red and shows no sign of connection. And one more detail is a Sprite capable of connecting with the Whisperer?

Pls answer me soon because I am in need of to use. 

Thanks

Having a problem since upgrade of the app. Doesn't seem possible unless the main unit updated as well. Valves close within a few minutes of being activated by manual start, or programmed schedule. Have not test with smart watering disabled, but it happens on manual starts, so not sure that is even a variable. The Zone still shows as actively watering in the application. If you submit a stop  action by pressing the red square,then restart, via the sideways triangle, the zone will come back on again. However, it shortly shuts back off, while still showing the zone as being actively watered. This is happening across all four of my zones. Curiously, if you unplug the controller after the valve shuts off, but the app still shows it watering, wait a bit, and then plugit back int-the zone comes backon shortly after reboot.

Tested countless times, hasn't finished a cycle in a month. The zone stops sending the 24v signal causing the pump relay to snap shut and turn off the water supply, or perhaps the zone valve. Either way, appears to be a very odd defect. Do I need a replacement unit?  (BTW, I have all smart fumctioms disabled) 

I have my controller in my garage here in the desert.  The transformer seems very hot to the touch.  Is this a problem??

What does the yellow triangle with the ! mean next to the schedule 

When I started running a scheduled daily program in conjunction with smart watering selected, for some reason zones will run at the same time.

Am I doing something wrong?  I have a one minute delay in my zones and when I didn’t have the program running the zones would run independently.

When I open the app while the two zones are running, it only displays one zone running.  I’m super confused.

Hello, I've noticed that 2 out of my 6 zones suffer from low to no water pressure. I tried removing the nozzles to test but the water kept barely coming out. I know the solinoids are working because the water is coming from the zones, but how can I understand why there is super low pressure?

Recently I have been having issues with zones 5-8 stop watering before the cycle is over, but keeps counting down and moves to the next zone and does the same thing. I have tried resetting the unit, re-linking the wifi, but doesn't seem to make a difference. Help!

Hi there,

My controller has been losing connection to the internet everyday for about two weeks. The controller light stays solid and my app says the controller is offline. I can only reset the controller by physically disconnecting the power supply for 10 seconds and rebooting. This is getting anyoying and is  becoming a daily routine. I have a wifi extender 2 ft from the controller location as well. If I can't depend on the controller to stay online, what's the point of having an internet based sprinkler system? What steps can I take to make the controller stay connected to the internet?

I installed as directed and only have three zones, but every time the system comes on all zones are watering simultaneously.  I installed the common wire as it was removed from the last controller and each valve wire is hooked to zones 1-3.  Any thoughts or ideals are appreciated.  Thank you

I installed as directed and only have three zones, but every time the system comes on all zones are watering simultaneously.  I installed the common wire as it was removed from the last controller and each valve wire is hooked to zones 1-3.  Any thoughts or ideals are appreciated.  Thank you