Good morning,

I have my netro sprite with green light showing connected.

Nonetheless, when executing the programs it shows "connection problems". When I try to run the programs manually, it keeps "connecting..." but does not open the valves so that it waters.

I have removed and reset the connection with the network, it becomes green again, but it still not work.

I have also reviewed the electrical connections on the valves, and they are ok.

I have also tested opening the valves manually, they open and water normally.

the only problem is when executing electronically... it keeps "connecting...." and does nothing.

Thanks for your support!

I have three zones with Whisperer 2 devices that have been installed for some time. It to skip watering above 90% and water extra at 60%. Soil moisture is currently at 56% and to says it isn't going to wTer again for like 40 hours. What's up with that? There is only a 38% chance of rain, and that is .1 inches so that can't be it.

Il programma notturno funziona regolarmente ma non funziona lo start manuale.

Anche entrando nel programma e selezionando esegui ora non parte.

Ho già provato a riavviare App centralina NETRO e router Wifi senza risultato.

Rimane in connessione ma non parte !!

My account Pier1972

Hi, 

I have some concerne about the time range. I set the Smart schedule to water just from 5am to 10am. But the Smart program seems to override this control. How can i ensure it would be respected? 

Could you please advise me on how to determine the specific requirements of my rose bush? While I have access to the data, I find it challenging to apply it without knowing the ideal conditions for my particular rose.

Thank you for your help.

Need to change the rainfall for the prior day, how do I do it? 

Da qualche giorno il dispositivo ha smesso di funzionare. Non irriga né manualmente né con il programma. Ho già provato a rimuoverlo dall’app e resettarlo, ma non è cambiato nulla. Cosa consigliate di fare? Grazie

Please

I have had smart cotroller netro for 3 years. Never problems! 

Now i d like to buy z1 pixie with hub! But is it essential the hub for smart controlling? And if yes the hub has to be connected by lan to the router? 

Salve, quanto deve risultare l’umidità del terreno in giardino? Il sensore mi indica sempre tra i 96 e 97%. 

Hello, I have 5 sprite-type irrigation controller units installed. In one of them, the irrigation stops after approximately 14 seconds on all channels, although it still appears as watering in the status. We have measured the electrical resistance and it is normal.

Why do my zones only activate for 2 seconds?

I have one sensor that is controlling 5 zones, in the last few months it has rained for several days and the humidity recorded has always been 100%. For three weeks however it has not rained anymore and the soil has started to dry out and so has the garden, because the sensor continues to report 100% humidity skipping the irrigation cycle. How can I unlock the sensor humidity reading?

Could you add a pause feature in Manual run? When I am running a zone, sometimes I need to halt the run and make an adjustment or fix a leak and then turn it back on. Right now, I have to stop the manual run and then start all over. 

My indicator led is burn out. whocan I replace it?

Hello, I have activated Continuous Monitoring on my Wispering gen2 which means I should get an emediate update when the moister has changed.

But I don't get any update/ change until the aut hourly upate of the measurement is done.

My app on my phone say that the zone is on watering but when i look outside nothing is happening !!!

Help for my controller dropping the wifi weekly?  I have to unplug the controller to reset and wifi works.  When on vacation my controller can't be unplugged so is there a fix or work around ?

I can't connect both of my two Pixie devices to Alexa — I can only control one.
How can I fix this issue?

Thank you.

I have a digital water metering in my house from my water supplier. So know the exact amount of water that ist running for all zones If netro ist running and watering the Garden. Unfortenately i can Not find an Option, to Tell netro how much water in qm per hour is running for wach zone. IT would be great If that could be implementated to have an exact number of qm water that ist uswd for watering each zone. So gar I know netro gives only an wstamated number of water used for wach zone, depwnding in size of watering area and Type of watering equipment.

Anyone else have problems with whisperer/whisperer 2? The ones I have just seem to stop working out the blue.  The current problem unit is a whisperer 2 which was sent to replace a broken whisperer.  It comes on, lights up, and shows 100% charged when plugged into a usb power source.  As soon as I unhook the power source it stops working, and oower button does nothing.