Más filtros

Constant Blinking

Seth McDonald
Actualizado 2019-05-31 00:32:04 
My device appears to be connected and working, but I noticed the light on the unit is blinking constantly.  Is it supposed to be doing that?
Ver: 4462   Respuesta: 1

How the smart watering is scheduled?

shaneduan
Actualizado 2019-05-30 15:57:58 

Maybe I missed something....


Just installed the controller and app. With “Smart” options Enabled with all zones, some zones will repeat themselves up to 4 times in one day, a few days in a week, some zone seems never scheduled at all(?). Is this how I should  use it or I have to use a fixed program only? How the auto scheduling is calculated?

Ver: 4412   Respuesta: 1

Using as a on/off switch

pgvolk
Actualizado 2019-05-29 14:59:55 
Have netro installed with sprinkler system. It works well. I have an above ground pool that I want install a solar heater to. I'd like to use the Netro to open a valve at a specific time and close it later, either at a time or interval. The longest program run is 60 minutes. I'd like to see something around 8 hours. Also, to be able to turn on/off via the app like the sprinklers would be perfect. Is this possible? I have looked but haven't found a way yet. 
Ver: 4490   Respuesta: 1

Netro offline and not watering

Mark
Actualizado 2019-05-28 22:23:43 

netro shows offline.  The app says zones are watering but no watering is occurring.   Plants are dying.


Retro device has a white light.


How do I fix this?

Ver: 4131   Respuesta: 0

Zones

José Miguel Salcedo
Actualizado 2019-05-28 20:03:07 
Why  can't I water two zones at the same time
Ver: 4529   Respuesta: 1

Subsoil moisture level

Swaroop Jay
Actualizado 2019-05-28 17:13:12 
How does Netro app calculate subsoil moisture levels? Note that I don’t have any sensors. Please advise 
Ver: 4544   Respuesta: 2

Still watered after *heavy* rain

Jon Storch
Actualizado 2019-05-27 19:41:14 

Hello, this morning my Netro still watered my front lawn after we had a massively heave rain last night.

I have Smart Zone enabled for all my zones. The Netro was supposed to be optimizing water usage.  

Why did it run this morning?

Thank you,

Jon Storch


 

Ver: 5122   Respuesta: 1

Don’t Stop !!

Eduardo Ariste
Actualizado 2019-05-26 11:27:42 
I have a problem. May be is the installation. The programm start watering ok, but when finish the App programm never stop watering until I desconnect the cable 24V. Somebody can help me ? It’s possible the cable connection wrong? (I have only 1 zone and the connection is: yellow to C, brown 1 and blue 2 ). Thank you very much
Ver: 4249   Respuesta: 1

Netro off line

Junglim Huh
Actualizado 2019-05-25 02:59:21 
I have been away for about 3 days now, and there has been a power failure at home. Netro has been offline since then for couple of days now. I know my wifi connection is good because my nest is working fine. What is up with this connection not being able to reconnect after accidental signal drop. 
Ver: 4753   Respuesta: 1

I have a ton of errors again for the last two weeks!

Joshua Berk
Actualizado 2019-05-23 18:39:21 

I just went to check on my sprinkler system since all of my grass has been dying and realized I've had errors on every watering attempt for the last 2 weeks!! I'm worried that a) it's not working and b) when it does start working it's going to flood my lawn again like it did last time because it tries to overwater for all the times it missed!


why aren't there any app notifications when this thing happens I shouldn't have to monitor the system manually to find out that it has not been watering for so long!

Ver: 4646   Respuesta: 1

Can't see answers to questions

Stan Bumgarner
Actualizado 2019-05-23 00:30:01 
Tema: General

I can see the question and can see that someone has answered it. How do I see the answer?

Thanks,

Stan

Ver: 4372   Respuesta: 1

Remote Access?

Oliver Pettit
Actualizado 2019-05-22 01:53:35 

Can you start the Pixie remotely?  i.e.  if I'm at work (i.e. not connected to my home network) I can start watering my garden?  If so is there anything I need to do to set this up?


Thanks, 


Oliver

Ver: 4850   Respuesta: 1

Manually skip next watering

Randy Ziffer
Actualizado 2019-05-19 16:47:13 
How can I manually skip the next scheduled watering?  I am watching it pour outside and the next scheduled watering is at 6 pm this evening.
Ver: 4517   Respuesta: 2

Have to reboot Sprite every day.

jpmeyer81
Actualizado 2019-05-19 15:04:11 

My Netro worked perfectly last season.  I left it plugged in through the winter and disabled the zones.  At some point during the winter, the light started blinking, and I didn’t worry about it until last week when I went to reactivate the zones.  The app indicated the sprite was offline, so I rebooted and it came back online with a solid light.  System worked with no issues.

The next day, the light was flashing again and app indicated offline.  This time I pressed the rest button and rejoined the network.  Again, worked for a day.  The next day, same problem - this time I rebooted my router.  Again it worked, but offline again the next day.  Don’t understand why it keeps losing connection this year.

Ver: 4678   Respuesta: 1

Is there a way to just set a test run of 1 minute per station?

Roianne Cox
Actualizado 2019-05-19 13:52:50 
When trouble shooting it would be nice to have a test run button so you could just run all the stations one minute. You can manually run each station but you have to do it for each station which is a pain. I have someone working on my system and I have to run it for them and stand there to run each station.
Ver: 4258   Respuesta: 1

Zone won’t turn on when manually turn it on

Dennis N
Actualizado 2019-05-18 17:52:30 
Hello I’m having an issue when I try to manually turn on a zone it doesn’t go on. It always worked and started doing this. I trying restarting the whole thing and when I turned the zone on by the Solonid the zone comes on fine. Any idea? 
Ver: 4304   Respuesta: 1

Sprite seems to open valve then fails to deliver water to the system

David Claridge
Actualizado 2019-05-18 13:21:53 

I have had my Sprite installed for a couple of weeks and all seemed well, but looking at my garden I realized it was not watering. When I turn it on manually I can hear a short buzz and water entering the valve, but there is no flow. I can open the valve manually and water then flows. I have reverted the valve to the old timer and it then opens the valve, so I don't think the problem lies there. 

I have the black wire on the valve connected to the common terminal, which was how it was set up on the old timer. I cannot figure out what the the problem is. 

I am an international user with a non-Netro PSU, but it seems to as specified: 24VAC 850mA Adapter AC-AC 100V-240V to 24VAC Power Supply Adapter UK PLUG

Can anyone help me overcome this problem with what otherwise seems to be an excellent system?

Ver: 4363   Respuesta: 1

Why is one zone being favored when all zones are identical?

Steven V
Actualizado 2019-05-18 13:08:55 
Just installed the system yesterday and I noticed zone 5 (of 5) for some reason is getting special treatment over the rest. All zones are set identically for the same types of grass, soil and sprinkler heads. However looking at the schedule zone 5 seems to be getting more attention than the rest (i.e.: only zone being watered during off days)  what's going on here? 
Ver: 4328   Respuesta: 1

Hot weather algorithm

Joshua Berk
Actualizado 2019-05-17 16:15:51 

I live in Arizona and it's not really hot yet but it's starting to get warmer and I noticed my rye grass is starting to die off and everybody else's is very green.  I think it's because netro isn't watering as often as it should be when it gets warmer. I'm aware I can set a manual schedule but that kind of defeats the purpose of why I bought Netro. So what I'm saying is I think an algorithm needs to be adjusted so hot dry climates get a little more watering for winter grass that's still in season before the Bermuda comes in.


Ver: 4769   Respuesta: 2

Whisperer stopped working

Pelle Fisk
Actualizado 2019-05-17 13:30:13 
My whisperer sensor stopped working after a few weeks. Any ideas?
Ver: 5151   Respuesta: 2