Hi there I have one of the whisperer that doesn't allow to adjust watering below 50%, 

Sensor number 2 in my installation. 

All the rest I can chose lower values

Hi there

I have read this article explains how to save water based on 

- seed type

- watering adjustement - EPA

- how tall to cut the grass

- how tall to leave the grass to growth ( deeper roots, the problem of loosing water by transpiration)

https://zulueta.com/regar-el-cesped-como-ahorrar-el-50-de-agua/

Currently the whisperer takes into consideration soil evaporation, but I do not know if transpiration is something to add to the watering algorithm

Hi today the smart schedule wateres while sensors above the 50% humid. I stopped manually. It is weird because the schedule shows to skip the zone but it watered anyway. Zone 3 and zone 4. Zone 1 is correct

May you check it?

Just a comment on the wishperee. They are too weak and easy to break, the sensor part that goes into the ground 

My kids just broke a couple playing soccer in the garden. It would be good if you develop one that can be fully placed in the ground and the only visible part is the solar panel

In the mobile application and in the web application I can check the history of the irrigation over a period of a year

I would like to know if you store data for more than a year and if it would be possible to export the data. For instance, last 3yr, 2yr

Thanks

Alfonso

The system has cancelled watering over the last 2 days. I see at the scheduler window. But I do not know what is the reason. 

Where can I get the logs, or info?

Thanks

Hi there none of the whisperers are sending data. 

I do not see any data of moisture, sun light, temperature etc.

I have changed to a recurrence of 1 hour to send the data.

Hi

I have checked that the irrigation modes

DEEP

EPA

REGULAR

FREQUENT

The only mode that saves water is ECO 

Or does a DEEP / EPA modes, will help me to save water compared to REGULAR or FREQUENT during a period of time ( I also have installed the whisperer) . Is the whisperer able to detect deep water?

I would like to stress the grass up to a point irrigation is needed, so swapping between DEEP and ECO to save water. But I cannot create a calendar where I could set up the watering mode per month for instance.

Any advice?

I irrigation zones attaches to the same sensor. 

I do not understand why the smart schedule do not schedules the same amount of time, and dates for the 2 zones.

Early in the morning? 6am etc...

Late in the night, 21, 22.h

Thx

Hi there

I would like to learn more about the watering modes. Specially I would like to know the difference between EPA and Deep. 

Make´s sense to use it in summer? specially in hot areas over 30ºC

Thanks

I have checked in the smart schedule that tomorrow is programmed to run zones that should be skipped.

I have set up the whisperer to skip run if moisture is above 40%. Current moisture is:

• Zone 2 - 92%
• Zone 5 - 70%

I have an issue/conflict  with the watering adjustments for the sensors and the Smart Zone Sheduling

I have seen something weird. 

• I Have set up the Watering Adjustment for sensors the following I describe o be sure about the problem
• Moisture to Skip watering 50%
• Moisture to Add watering 30%
• Duration 5 minutes (only) -- it is a check

• The Smart Zones are st up the following
• Smart Zone - enabled
• Mode - regular

The watering run today only 5 minutes, when the smart  schedule  defined by the system was above that. As you can see, tomorrow watering says different time runs per zone, but it will run a maximum of 5 minutes. This means that the sensor configuration overrides the Smart Zone. And it should not.

As far as I understand the Watering adjustemt is to add EXTRA watering when needed based on the moisture level. Attached picture

Prior to this setup I had the Duration for Watering Adjustment for 15  and 10 minutes, and you can see in the past days runs, that always run for 15 -10 minutes depending the zone/sensor. - Attached picture

In previous weeks, it was working fine and adding extra watering when need it to keep the moisture levels.

Any idea?

I DID THE CHANGES PROPOSED BY NETRO  and it is not working

Take a look the screen shots

Zones 3,4,5 it is below the 30% trigger

Sensor 2 says moisture level is 7% after very heavy rain, but the weekly view says 92% 

When you select the year view you see only 12 months. Instead it would be useful to add 13, so I could compare year over year the same month.

Not only the last 12 months